Jump to content
SAU Community

Recommended Posts

mates 180 is written off because of some stupid f**king wog parking in a no standing zone and 1m from the curb and because the 2 cars in front hit the breaks

not too happy

your mate was too close to stop = fail

A rear ender like that is usually open and shut, 100%, tailenders fault.

Hope your all OK and no-one was hurt.

your mate was too close to stop = fail

A rear ender like that is usually open and shut, 100%, tailenders fault.

Hope your all OK and no-one was hurt.

i think ive busted my shoulder up , gonna go get it checked out tomorrow

my mates devastated cause he just got the car with a loan and now it seems to be written off

sure its not my car but im on the verge of tears cause it brought back memories from a major car accident i was in a few years back :P

your mate was too close to stop = fail

A rear ender like that is usually open and shut, 100%, tailenders fault.

Hope your all OK and no-one was hurt.

+1

hope u guise are all ok

i dont really trust anyone on the roads, fkt if i sit any closer than 3 car lengths behind ppl. been a passenger in similar situation, with a mate who is a hero that can drive close to ppl

thanks

+1

hope u guise are all ok

i dont really trust anyone on the roads, fkt if i sit any closer than 3 car lengths behind ppl. been a passenger in similar situation, with a mate who is a hero that can drive close to ppl

i sit atleast 4 cars away from the car in front , we just came off the lights and then it happened :)

looks like me n my mate will be turning it into a sil80 now :P

thanks

i sit atleast 4 cars away from the car in front , we just came off the lights and then it happened :)

looks like me n my mate will be turning it into a sil80 now :P

yeah, i just consider everyone else on the road is a tard.

hope ur aches n pains arent too bad when u wake up in the morning.

on the plus side...... u guise have a new project :)

yeah, i just consider everyone else on the road is a tard.

hope ur aches n pains arent too bad when u wake up in the morning.

on the plus side...... u guise have a new project :)

we had a project before we went to get kfc

replace the Y fork in his transmission :D

got the part on hold at nisswreck but im guessing we will be haulin s13 parts around now :)

were also going to order coilovers , bucket seat , sway bars , strut braces , caster rods and brake cylinder stoppers for both of our cars but im sure thats on hold now :(

oh well , life goes on , cars are repairable

end of the day , too many tards on the road :P

yeah sure. whenever i need to take them off again or free one weekend i'll let u know.

btw kye they look tough. Just need those coilovers now.

Edited by Luke_ENR34
yeah sure. whenever i need to take them off again or free one weekend i'll let u know.

btw kye they look tough. Just need those coilovers now.

haha yeah tell me about it. its pretty dumped but just needs another inch or so to set it right off.

ill be bottoming out on small pebbles by the time i get it low enough :P

abit mexican at the front though! going to run smaller tyers and more camber i think

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...