Jump to content
SAU Community

The Sa Wasteland

Cubes

By Cubes,
in South Australia

 Share

Recommended Posts

  • Replies 36k
  • Created
  • Last Reply

Top Posters In This Topic

  • Damo_R34

    2820

  • scandyflick

    2266

  • Madaz

    1919

  • craig R33

    1717

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Ryanrb25
Ryanrb25

i went for a hills run last night in the 31 with the roads very slippery.....was much fun. Had to bed in the bottom end bearings so yea..took it for a strap.

DSTROY
DSTROY

Hey Ryan, do you know how to fit a set of drop spindles to the front of a hilux???

Madaz
Madaz

Dam straight Damo would rather do SAU them heroin gts4 are 4.1 because they share the same parts from the gtr i think r32 gtst is 4.3 because of the lack of torque from the rb20

Posted Images

scandyflick Grand Master

scandyflick

Posted
Posted

*reads kell's vent post*

uh shit. calling that guy an immature dropkick is an insult to immature dropkicks the world over. worst f**kin excuse ive ever heard, dude knew what he was getting into from the start, and to turn around and say that is incredibly low. but as pete said, better early than late with this. better luck next time. :P

Damo_R34 Grand Master

Damo_R34

Posted
Posted

ugh, knew it, sorry Kel but i didnt like him from the start, definately seemed like he thought he was so much more upper class than the rest of us, Rubbing in how bad maccas is for us, after us laughing and saying how much we dont care, saying he only eats "gourmet", then talking with him about my car, after he bought it up, and him saying "i dont even know why you guys bother". Much better off without him, hes a toss.

bezender Grand Master

bezender

Posted
Posted

my mate and i just cooked an awesome meal to break in his new webber.

cooked a whole snapper with lemon juice, coriander, salt, pepper, red curry paste and some white wine. served it on wok tossed veggies.

was so good i had to share with u guys

IMG_0092.jpg

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      I definitely know the first rule here, look first, ask second. I've seen many people get roasted 😂 I found a few diagrams for the RB, but I'm yet to come across one for the VQ. From what I have read, the pump gets the +12v along with the FPCM, and it's the negative wire that gets passed through the resistor to regulate the voltage. So I assume I can just ground the negative wire at the pump to eliminate the FPCM control. But I really wanted to see the VQ circuit diagram first to make sure I understood it correctly. Once the new pump is in I'll do some testing to see how it behaves, and in the meantime, I'll keep looking for a wiring diagram. Thanks for your help mate, your time is greatly appreciated.    
    • GTSBoy
      Jacks that fit under GTR lips that can reach the subframe?

      By GTSBoy · Posted

      Maybe? I have the Supercheap ToolPro low thingo. It has a somewhat smaller diameter lifting "bowl" than you would expect on a workshop grade trolley jack, and a split rubber pad to suit that diameter. It clears the "N1" style skirts I have. Probably wouldn't if the jack's bowl and a suitably larger rubber block were in use. Having said that though.....you only need the rubber block to exist on the inner side of the pinchweld, so could carve away any rubber that fouled the skirt, leaving some there for "insurance" </simples>
    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      I used to do that (sills with rubber jack block).. ... then I got side skirts, and there's no way for the jack to actually work there, the jack pad itself on the jack is too big. Is the answer to use a... smaller (?) jack? Hmmm.
    • Murray_Calavera
      Jacks that fit under GTR lips that can reach the subframe?

      By Murray_Calavera · Posted

      I have too much trauma from every skyline I've ever seen having crushed jack points/pinch welds lol.    Yep, works 100%, it's what I use when I'm using the quick jack. Don't know why I can't also bring myself to do the same thing when I'm using a jack. I blame the skyline PTSD. 
×
×
  • Create New...