Jump to content
SAU Community

The Sa Wasteland

Cubes

By Cubes,
in South Australia

 Share

Recommended Posts

RubyRS4 Grand Master

RubyRS4

Posted
Posted
would anyone happen to know where i could go get a nice sounding exhaust for my lil 125cc bike? ^_^

East 50s on Payneham Road. Tell Brian that Reuben sent ya.

Or try see what the boys at Pooraka track has on their wall.

  • Replies 36k
  • Created
  • Last Reply

Top Posters In This Topic

  • Damo_R34

    2820

  • scandyflick

    2266

  • Madaz

    1919

  • craig R33

    1717

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Ryanrb25
Ryanrb25

i went for a hills run last night in the 31 with the roads very slippery.....was much fun. Had to bed in the bottom end bearings so yea..took it for a strap.

DSTROY
DSTROY

Hey Ryan, do you know how to fit a set of drop spindles to the front of a hilux???

Madaz
Madaz

Dam straight Damo would rather do SAU them heroin gts4 are 4.1 because they share the same parts from the gtr i think r32 gtst is 4.3 because of the lack of torque from the rb20

Posted Images

Chris#3 Experienced

Chris#3

Posted
Posted (edited)

Edit: This is the extract from the info bulletin 3.

Roll Cages

Due to the increased risk of occupant injury in vehicle accidents the fitting of full roll cages are not permitted.

However, the fitting of a roll cage rearward of the driver is permissible providing that:

a. No part of the roll cage is contactable by vehicle occupants when positioned in their normal seating

position.

b. The roll cage is at least 150 millimetres rearward of the front seat occupants when the front seats are

located in the most rearward adjusted position.

c. All rear seats and seat belt assemblies fitted in the rear compartment are removed.

d. The operation and effectiveness of the front seat belt assemblies is not affected in any way by the roll

cage.

e. That no person travels in the rear of the vehicle at any time.

Also, the car has to be re-registered as a 2 seater.

Edited by Eddyfier
AndrewJZX100 Mentor

AndrewJZX100

Posted
Posted (edited)

Wooo

Put some new plugs in my car and theres a noticable improvement in smoothness now :woot::)

Still needs the oils and clutch to be done this friday, but cheering I could work on it for a few hours (I put the stock intake back on also) and come out of it with something positive, not really often that happens :)

Once the clutch is replaced, all it'll need is a touch up tune and then hopefully I can ease up spending money on it and just concentrate on driving it.

while I was out there I also measured my ride height after looking through the regency thread, it's at 345mm front and 355mm rear. In other words, it's legal height, and therefore CANNOT be defected for too low :)

Edited by AndrewJZX100
DSTROY Grand Master

DSTROY

Posted
Posted

Edit: This is the extract from the info bulletin 3.

QUOTE Roll Cages

Due to the increased risk of occupant injury in vehicle accidents the fitting of full roll cages are not permitted.

However, the fitting of a roll cage rearward of the driver is permissible providing that:

a. No part of the roll cage is contactable by vehicle occupants when positioned in their normal seating

position.

b. The roll cage is at least 150 millimetres rearward of the front seat occupants when the front seats are

located in the most rearward adjusted position.

c. All rear seats and seat belt assemblies fitted in the rear compartment are removed.

d. The operation and effectiveness of the front seat belt assemblies is not affected in any way by the roll

cage.

e. That no person travels in the rear of the vehicle at any time.

this the only part i would be concerned about, what part of your body do they measure from??? im not sure the cage would be far enough back.

Chris#3 Experienced

Chris#3

Posted
Posted
this the only part i would be concerned about, what part of your body do they measure from??? im not sure the cage would be far enough back.

I'm not 100% sure but I think they put your drivers seat to the rear most position on the rail (I'm not sure if the recline the seat as well) and measure from the very front of the cage to the very back of the drivers seat.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • tidi0x
      Wheel Sizes & Offsets For Skylines

      By tidi0x · Posted

      Wanted to add some of my R33 GTST  R34 GTR wheels, 18x9 ET30 with 255/35/R18 PS4S'   BBS RE-V7 029 18x9.5 ET22 with 255/35/R18 PS4S' Needs a bit of camber   
    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      Lamb roast on Saturday will be different 🥲
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • GTSBoy
      RB25DET with solid lifters - which cams ?

      By GTSBoy · Posted

      I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
×
×
  • Create New...