Jump to content
SAU Community

The Sa Wasteland

Cubes

By Cubes,
in South Australia

 Share

Recommended Posts

  • Replies 36k
  • Created
  • Last Reply

Top Posters In This Topic

  • Damo_R34

    2820

  • scandyflick

    2266

  • Madaz

    1919

  • craig R33

    1717

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Ryanrb25
Ryanrb25

i went for a hills run last night in the 31 with the roads very slippery.....was much fun. Had to bed in the bottom end bearings so yea..took it for a strap.

DSTROY
DSTROY

Hey Ryan, do you know how to fit a set of drop spindles to the front of a hilux???

Madaz
Madaz

Dam straight Damo would rather do SAU them heroin gts4 are 4.1 because they share the same parts from the gtr i think r32 gtst is 4.3 because of the lack of torque from the rb20

Posted Images

Ryanrb25 Grand Master

Ryanrb25

Posted
Posted (edited)

considering before the yen went up you could buy them at wheel works for 3600 without tyres, now it's probably near 4k. Ill sell mine with tyres for 3k :D if i dont get that there's no parting with them. Ill keep them and get the fronts widened and put them on the GTR.

Edited by Ryanrb25
J - Rad Veteran

J - Rad

Posted
Posted (edited)

Yeah, just checked. Looking at $3,500 without tyres brand new for 18x9. Mine are 18x8.5 and 18x9.5 so for staggered it might be more expensive.

Edit: That was from some bodgy looking American website. Couldn't find much pricing anywhere else.

Edited by muirsky
craig R33 Grand Master

craig R33

Posted
Posted
Yeah, just checked. Looking at $3,500 without tyres brand new for 18x9. Mine are 18x8.5 and 18x9.5 so for staggered it might be more expensive.

Edit: That was from some bodgy looking American website. Couldn't find much pricing anywhere else.

if thats 3,500 u.s $ you looking at a shit load more due to the gay $ AU

scandyflick Grand Master

scandyflick

Posted
Posted
yeah cant find any info that says they are any more effective than the factory grounding

i cant see any benefit. if i was gonna improve my earths id spend a few dollars on 0 gauge wiring and redo all the major ones.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      NC MX5

      By Kinkstaah · Posted

      I am well aware as I did rant at him to buy a MX5, buy the 2.5 before he DIY'ed it, etc as well as do things to the holden. He will obtain a ND. It's the best of both worlds. They look great in person, definitely the best looking one. Just a matter of time now.
    • r32-25t
      NC MX5

      By r32-25t · Posted

      Remember this is the same person who said he’d never own an nc 
    • zique
      Ceramic turbine damage to engine - what did yours do?

      By zique · Posted

      ouch! how is the car now?I had sold my gtr but have been looking into some on trademe and a 260RS but I wouldnt be keen on any repairs needed on them
    • MBS206
      NC MX5

      By MBS206 · Posted

      This sounds like someone who would have owned an R33 in their past... It's okay, I'm 100% picking up what you're putting down Mark.
    • MBS206
      Jacks that fit under GTR lips that can reach the subframe?

      By MBS206 · Posted

      Just back on what was raised about jacking off the the tow/tie down point on the front of cars. I've used it plenty. I've also watched it on a car where you could see it move the front end of the car. It was like the front end/whole car being tweaked and twisted a bit. I will say, I struggle to find good jacking points on MOST cars. The ones that have good points, I then normally struggle to find a jack tall enough to make the car change height!   One of my go to points for either the jack, or the axel stands though, is either a suspension pickup point, OR a subframe to chassis major bolting point. I actually think its the subframe on my R33 that has a bit of a bend in it, from being jacked in the middle too. However, it could have been one of my many other cars I've had over the years! Or it could also be the from me jacking it up, and the fact the top of the front radiator support isn't there, so it can allow the front of the car to move and bend etc.
×
×
  • Create New...