Jump to content
SAU Community

Recommended Posts

fours n more dyno and automotive. They are in pooraka.

Stripped my 25det down before i brought it to make sure it was all good, did the conversion, added new bits, dynoed, tuned, have done the works to my car and the engine hasnt missed a beat in over a year of limiter bashing now lol.

82602011 is their number, brenton is who you want to speak to and tell him Luke with the R31 put you onto them.

ahk cheers , are they expensive ?

umm well they arent cheap, but would say competitive with boostworx pricing i reckon. You can be guranteed no corner cutting will be done and they are very thorough. He doesnt let a car leave his shop till he is confident it is 100%

umm well they arent cheap, but would say competitive with boostworx pricing i reckon. You can be guranteed no corner cutting will be done and they are very thorough. He doesnt let a car leave his shop till he is confident it is 100%

ohk thats good then , ill give em a call tomorrow ! :D

cheers

KN6 K is on the plate, few listed for KN6 reckon mines the pearl one.

ah yours is Dark Grey and mine Gun Metalic Grey Paint Codes

can someone point me in the right direction of a workshop to get my engine rebuilt ?

i heard boostworx has a 3 month wait :D

and yes i have read the workshop list.

why not Tyrone from Import Compliance Systems or you got a quote and there dear

Mitch, also try Lewis Engines.

http://www.lewisengines.com.au/category9_1.htm

Boostworx are more expensive as they send off some of the parts to other shops to get done, where-as somewhere like Lewis Engines do everything in-house, so you have no middle man, hence the cheaper price.

see Toyo Tyres pulled all sponsorship from DA? New owners are "Ninety Degree Entertainment". They were going to only have one championship round for the 09 series at Oran Park unless a naming rights sponsor was signed. Phew!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.  
    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
×
×
  • Create New...