Jump to content
SAU Community

Recommended Posts

fours n more dyno and automotive. They are in pooraka.

Stripped my 25det down before i brought it to make sure it was all good, did the conversion, added new bits, dynoed, tuned, have done the works to my car and the engine hasnt missed a beat in over a year of limiter bashing now lol.

82602011 is their number, brenton is who you want to speak to and tell him Luke with the R31 put you onto them.

ahk cheers , are they expensive ?

umm well they arent cheap, but would say competitive with boostworx pricing i reckon. You can be guranteed no corner cutting will be done and they are very thorough. He doesnt let a car leave his shop till he is confident it is 100%

umm well they arent cheap, but would say competitive with boostworx pricing i reckon. You can be guranteed no corner cutting will be done and they are very thorough. He doesnt let a car leave his shop till he is confident it is 100%

ohk thats good then , ill give em a call tomorrow ! :D

cheers

KN6 K is on the plate, few listed for KN6 reckon mines the pearl one.

ah yours is Dark Grey and mine Gun Metalic Grey Paint Codes

can someone point me in the right direction of a workshop to get my engine rebuilt ?

i heard boostworx has a 3 month wait :D

and yes i have read the workshop list.

why not Tyrone from Import Compliance Systems or you got a quote and there dear

Mitch, also try Lewis Engines.

http://www.lewisengines.com.au/category9_1.htm

Boostworx are more expensive as they send off some of the parts to other shops to get done, where-as somewhere like Lewis Engines do everything in-house, so you have no middle man, hence the cheaper price.

see Toyo Tyres pulled all sponsorship from DA? New owners are "Ninety Degree Entertainment". They were going to only have one championship round for the 09 series at Oran Park unless a naming rights sponsor was signed. Phew!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • all brand new unit from Tomei, fluid, bearings, etc. Tomei said they call it a 1.5 lsd because its 100 percent lock up under acceleration and 50 percent under deacceleration.  as I mentioned I used their fluid, install and their break-in procedure, (alot of figure 8's) but even when driving straight, or even slowly backing out of garage for first time, (at 2 mph) then driving to and from figure 8 parking lot, each tire in the rear would sporadically grab, skip, bounce, shutter and skip, shutter back a force I could feel causing clutch to slip then grab, at any speed. shaking entire car. I removed unit, since I put stock back in and all is fine, via process of elimination, its something with the lsd unit itself. I wasn't going to beat up the entire car more or change anything else for no reason as I had a feeling something in the lsd itself was wrong as everything was fine before this alone was installed and I rechecked over everything else after first time backing out I suspected an issue. I'll probably sadly already need new tires now just from trying to drive it 5 miles and performing the figure 8 break in. but if someone has any ideas I'm all ears 
    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
×
×
  • Create New...