Jump to content
SAU Community

Recommended Posts

Front part of the exhaust will need changing too. Buy a GTT, much much simpler when considering registration hassles too....

what do you mean?

the engine i have found includes mainfold with the turbo on it.

and no, im not buying a gtt.

i couldnt give a rats about rego now lol once the rego runs out end of june she wont be registered again untll october,.and thats cause of the fact i got 3 shows on 3 consecutive weekends, and rego up here is cheaper than it is in adelaide :P

what do you mean?

the engine i have found includes mainfold with the turbo on it.

and no, im not buying a gtt.

i couldnt give a rats about rego now lol once the rego runs out end of june she wont be registered again untll october,.and thats cause of the fact i got 3 shows on 3 consecutive weekends, and rego up here is cheaper than it is in adelaide :P

Front/dump pipe part that bolts to the back of the turbo will be different to your NA

You'll need to change engine number for registration and also more than likely *(I'm not 100% sure) you'll need an engineers certificate because of the turbo addition.

Front/dump pipe part that bolts to the back of the turbo will be different to your NA

You'll need to change engine number for registration and also more than likely *(I'm not 100% sure) you'll need an engineers certificate because of the turbo addition.

oh ok well getting a dump pipe aint that hard lol

not sure on the engineers certificate i know i have to fill out some form letting them (regency i think) know about the engine swap and they send me out a list of stuff i have to change, something like that. ill give em a buzz tomoro

diff, suspension, drive shaft.

im just plucking but there could be other potential things in there.

only benefit i see in moding the current 1 is you wont have to swap over your body kit. thought that woulda been an easier job than swapping an otherwise perfectly good engine out of a car.

and the stereo of course

Edited by Inline 6
diff, suspension, drive shaft.

im just plucking but there could be other potential things in there.

only benefit i see in moding the current 1 is you wont have to swap over your body kit. thought that woulda been an easier job than swapping an otherwise perfectly good engine out of a car.

and the stereo of course

diff i can get away with, i dont intend to be doing burnouts anyway

suspension is same as gtt (my lowered king springs and shocks are from gtt), clutch is gtt too

Edited by MissR34

- 1 AGAIN to the media.

we are being blamed for a hep. A outbreak in our semi dries tomatoes. funny that seeing as :

A: we do not make them, they are grown/dried/packaged in queensland.

B: we do not supply interstate ( where other cases have been found)

C:we are haccp certified.

D: there are 3 other major suppliers of semi dries in adelaide, all of which come from the sphincter of the universe where food safety is nearly non existent. (ours are aus)

Once again, media blabbering without re-search.

:P

He still doesn't know :D His son does and also works with us, he sent me a message not long ago saying people were laughing and beeping all the way home and the old man couldn't figure out why :(

thats pure gold. lol nice work hahaha

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia body...
    • This. A 3d wheel alignment is like $120...just take it to the shop. Since theres probably multiple adjustments that need to be made after changing something. Mine has front/rear lower arms, traction rods, tension rods, camber arms, toe arms, front upper arms, hicas kit, sway bars and coilovers. I measure from the edge of the bolt holes on the originals and set the same length on all the adjustable stuff to dial it as close as I could to OEM. Took it straight for alignment; it didnt feel right at all...after alignment, it feels perfect. Similarly i've just changed the springs on another car; and I still needed multiple adjustments to bring it back in spec.
    • A full Veilside kitted JZA80 Supra in Meriken park in Kobe city a few weeks back
×
×
  • Create New...