Jump to content
SAU Community

Recommended Posts

Nengun has the pfc boost control for around 470 delivered? I guarantee Luke ENR can get it cheaper too... Both are fine, just depends if you want another device in your cabin or not i guess.

i didnt look on nengun. must do me thinks lol

Cara if your after 300 at the moment then you will something like a GT3071 + cams +porting + lots of boost and you may just still fall under 300kw but it will be more responsive that the other option which is a GT3076 which will make 300 with cams and has the potential to make more.

As for the RB25/30 build, if you are after a big power engine then do yourself a favour an go for a 26 head straight away. 26's have all the good stuff straight away like solid lifters and cams to suit as well as not having the VTC gear which you can't run with big cams. Although the NEO's have the solid setup they have a problem with an exposed oil gallery once you go over 9.25mm of lift and therefore your potential power is limited. The other good thing about the 26 heads is the availability of aftermarket parts like a wide selection of cams, valves, springs etc etc.

if i got 26 head it means im gonna have to muck around and get another ecu and whatnot when ive already got one now. was going to go custom cams anyway with the 500rwkw build, they cost the same as buying them off the shelf (around $1200)

great, another option for them to bump up prices

damn, i hope they dont shelve the mobil 98 octane... thats gonna poop on my parade (caltex dont sell any form of 98 here in SA but they do interstate - what gives? :(

-D

EXXON are going to become suppliers only have no fear Ben there will still be a mobil 98 just branded something else may even be caltex

dad said caltex make some of there own fuel but they wont have enough to supply 302 new stations with fuel

also there is a clause that they have to purchase fuel for the next 5 years

I wanna be different, so i am thinking of a Rb25/26 (RB27) conversion, i think someone in SAU:Perth did one. It had around 400rwkw, saw it in a old HPI mag, i don't wanna go to the same extent he did, but finding info is near impossible. Anyone like to help out later down the track when i blow my engine up and rebuild to a RB27?

ATM i am planning for around 250rwkw or above. I have nismo 740cc injectors on the way, have front/dump pipe & exhaust manifold, a Haltech e11v2, and still deciding on either a GT3071R or GT3076R. The guy i bought the front/dump pipe from had a GT3076R making 280rwkw on a RB25, was saying when it hit boost was just wheel spin.

Im running standard turbo at 12psi, making a little over 200rwkw with power fc, fmic, free flowing exhaust, bleed valve. standard fuel pump, coilpacks, injectors, cams + gears, etc. i've considered the turbo upgrade options, but have something else in mind at the moment. high flow turbo will see 250ish, maybe a bit less, but if your building a dyno queen, your gonna need something like Ryan has on his 33, i think its 3582R? or if its a dyno queen, read: not for road use, you will probably benefit from a high mount turbo setup.

i run a built engine and big turbo, so does that mean u im a "DYNO QUEEN"...???

so if u run a big turbo like a GT35/40 it makes u a"DYNO QUEEN"" also WTF?????????

u dont see me entering stupid dyno comps

the only reason my engine is FORGED is coz a certain "well known workshop" blew my motor up on their dyno after i spent big $$$ with them!!!!!!!!

I wanna be different, so i am thinking of a Rb25/26 (RB27) conversion, i think someone in SAU:Perth did one. It had around 400rwkw, saw it in a old HPI mag, i don't wanna go to the same extent he did, but finding info is near impossible. Anyone like to help out later down the track when i blow my engine up and rebuild to a RB27?

ATM i am planning for around 250rwkw or above. I have nismo 740cc injectors on the way, have front/dump pipe & exhaust manifold, a Haltech e11v2, and still deciding on either a GT3071R or GT3076R. The guy i bought the front/dump pipe from had a GT3076R making 280rwkw on a RB25, was saying when it hit boost was just wheel spin.

I don't know why people say that a RB25 with a RB26 crank/rods will make a RB27 because it won't.

RB25/26/30's all have the same bore 86mm so the only difference between the engines is the stroke. So guess what, if you fit a RB26 cranks in a RB25 you end up with an RB26 because the bore and stroke is the same as an RB26.

or might hit up a 1jzgt-e for it..

mad custom work.. just want something special :(

Why don't you do what a bloke in the States did with TE27 and fit a 1UZ-fe, I'd say that you'd be the only person in Australia with a V8 keto. Having said that the CA would still make more power.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...