Jump to content
SAU Community

Recommended Posts

all a bit of a shrug to me tbh.

... Im one of the nice ones, letting others in, attentive 100% of the time, total control, no accidents, no speeding fines nor even a "rbt" in 10yrs

I must be the fonz.

:devil: 1

that soo frieken gross man...yuck yuck yuck... now i got to go to work feeling like throwing up in the weetbix haha reminder dont eat any weetbix with best before date "00:00-04:00 23 AUG 10 51" haha jks

very disturbing that you search that shit damo

I just sent in a few "hoon reports" of my daily spottings... commodore pegging it down the road, commodore pegging off from traffic lights, utes speeding down freeways, cop car cutting off traffic driving off straight ahead from a slip lane, elderly people driving like a menace slowing traffic no clue where they are or where they want to go etc and so forth... wonder if I'll get a reply from them :devil:

same, i just reported an old lady for not indicating when changing lanes. good damn hooligans.

or on takeoff?? =\

probably should have mentioned that after villis... u had some knocking as you get the car rolling

lol. yeah, no more knock on take off either. pain in the ass driving with shot mounts. knocks at every opportunity, crunches when you snap a gear...

... all sorted now though. :devil:

firstly, my only poisons are booze and cigarettes

i decided to perform a social experiment with my housemate "milky".

milky loves his weed, but he hates spiders so i set this lil trap for him

milkysweed.jpg

i'll let you all know what happens when he gets home :thumbsup:

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...