Jump to content
SAU Community

Recommended Posts

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

have you tried cranking over crank with a ratchet just to make sure it hasnt seized, if it hasn't as long as when you changed all your electrics over you put your series 1 coil packs and igniter over then you should use the series 1 ecu and it should work. only thing left is a loose connection or blown fuse or realy, easist to pull out all the fuses check if they are ok, i dun remember how to check relays mabye try swaping the mayor ones around if there are any and smell then see if they smell burnt out, then if that fails start checking ALL of your connections you have made make sure everything is hooked up and hooked up correctly and properly

Dont dry cell batteries need a charger with a lot more oomph than normal batteries?

What sort of battery do you have and what charger are you using?

I had my dry cell on charge with a small charger for quite a few days...lol it didnt work at all :)

Maybe try a new battery (not a new dry cell they can be $$$$) at least it will rule it out.

well i brought a new battery its worked well sort of

it primes everything up all sweet n shit all lights work

but its wont fire the starter motor

can i have put the wires on the wrong terminals on the starter motor

does anyone have pic of whet side they go on ??

Noone on here will be able to tell you with certainty what your problem is. Grab your multimeter and start by checking the voltage across the starter motor when trying to start and if that's no good check for continuity (resistance) between the ecu (pin 43 i believe, but check this) and starter, check the fuse etc. There isn't much really to the circuit apart from the ignition barrell. If the ECU isn't sending the correct signal (eg. series 1 vs 2) then you have basically no chance.

Is the ECU spitting out any error codes? Is there power to anything else? (water temp sensor, CAS, AFM, coils, fuel pump as random examples)

Edited by govich
Noone on here will be able to tell you with certainty what your problem is. Grab your multimeter and start by checking the voltage across the starter motor when trying to start and if that's no good check for continuity (resistance) between the ecu (pin 43 i believe, but check this) and starter, check the fuse etc. There isn't much really to the circuit apart from the ignition barrell. If the ECU isn't sending the correct signal (eg. series 1 vs 2) then you have basically no chance.

Is the ECU spitting out any error codes? Is there power to anything else? (water temp sensor, CAS, AFM, coils, fuel pump as random examples)

i know that but im elimanating anythin possiable

error codes ?? how do i find this out

and where is pin 43 on the ecu

my hole wiring loom in s1 any wires or elec componants are s1 all i dont was use the head and block

when you say you dont have any spark or inj do you mean the starter try's to crank it but it doesnt turn over just going tick tick tick?? are both the injectors and spark not working how have you tested for both? is the fuel pump priming?

Try swaping with a known good series 1 ecu, make sure the ignitor pack is plugged in properly, double check you havent missed pluggin in any of the connections. are the ignigtor packs known to be good?? stupid question but did you transfer over your spark plugs sometimes people forget the obvious things.

when you say you dont have any spark or inj do you mean the starter try's to crank it but it doesnt turn over just going tick tick tick?? are both the injectors and spark not working how have you tested for both? is the fuel pump priming?

Try swaping with a known good series 1 ecu, make sure the ignitor pack is plugged in properly, double check you havent missed pluggin in any of the connections. are the ignigtor packs known to be good?? stupid question but did you transfer over your spark plugs sometimes people forget the obvious things.

i have plugged everythihng in

the pump is priming

its turning over

the ignightor pack is pluged in

spark plugs are in

i tested them all

spark plugs not sparking

inj not pulsing

all tested

  • 3 months later...

have ya found out what the problem is yet with your car

i have a similar problem at the moment. The car was running previously but then now wont start. The engine is turning over but just wont start.

different power fc's have already been tried. Spark plugs, coilpacks, different CAS will be looked at monday.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...