Jump to content
SAU Community

Hiclone - ? - Another Myth To Grab Average Car People? Snake Oil?


Recommended Posts

I'm assuming this is just like all the other 'Gain power now, save fuel..'

http://www.fuelsaver.com.au/hiclone.php

Thoughts?

After looking through the web site, it all feels like rubbish, but......

From web site....

Turbo Engines

For Turbo vehicles we suggest installing Hiclones in two locations.

The first Hiclone is installed near the intake manifold; after the Turbo or intercooler; to improve combustion and economy.

The second part is installed near the air filter, before the Turbo. This part helps the Turbo Impellor to spin, reducing Turbo lag, bringing the boost in around 400-500rpm earlier.

It is also possible to install extra Hiclones in power or economy positions to further improve the vehicle. We have a lot of customers with up to 6 Hiclones installed on one vehicle.

Please note the line - AFTER THE Turbo ??!!!

Edited by Zebbie

I read an article a little while ago where they tested a bunch of these power enhancing/fuel saving type devices in a stock car on a dyno, and the best you could hope is that they did nothing, most of them restricted some power and one even set the test car on fire :)

surely you jest?!?! I mean look at the fking thing. and the diagrams... ooooh swirling air.... just get out a $100 note and set it on fire. you will get all of the benefits of a hi-con with the potential for engine damage.

i've bought a new RB20E long and i'm building it up to run quad hiclones... should run 9's all day

Edited by joeyjoejoejuniorshabadoo

This is my favourite quote from their website:

The ECU will need time to re-learn (about a week) this is why dyno shops who test products by doing one run without, and one run with any product don't know how to use a dyno on an EFI car.

So basically they are saying everytime you do back to back dyno tests you are wrong, and thats why no one has proof their product actually works.

Utter BS

This is my favourite quote from their website:

The ECU will need time to re-learn (about a week) this is why dyno shops who test products by doing one run without, and one run with any product don't know how to use a dyno on an EFI car.

So basically they are saying everytime you do back to back dyno tests you are wrong, and thats why no one has proof their product actually works.

Utter BS

anything to make a dollah!

I read an article a little while ago where they tested a bunch of these power enhancing/fuel saving type devices in a stock car on a dyno, and the best you could hope is that they did nothing, most of them restricted some power and one even set the test car on fire :D

:w00t:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...