Jump to content
SAU Community

Recommended Posts

hi this is all to common

my best mates white r33 was stolen last night

from marsfield between 9pm and 730am today

it had a tarnarbi exhust witch was very loud, dump pipe

Plates "MUN 61E"

standard rims M SPEC kit

also had boost controler

if it is seen call me Scott 0414905905

or glen (owner) 0402312197

cheers

Link to comment
https://www.sau.com.au/forums/topic/18989-stolen-white-r33/
Share on other sites

PHUCK ME!! Another one!!!!!!!!!!!!!

Sorry to hear bout it, i will keep my eyes posted...again!!!

Was it in a garage, alarm????

Im gettin the feeling there is someone out there either building up a R33 or selling parts cheap!!!! The phucker better not run into me!!!!!!!!!!!!!! Theyve been warned!

Link to comment
https://www.sau.com.au/forums/topic/18989-stolen-white-r33/#findComment-400780
Share on other sites

Sorry to hear it dude - ive seen this car around the Ryde area. Hearing this just brings it a little bit closer to home - like say on my doorstep.

Hopefully like URMINE, it is recovered and in reasonable condition.

Post pics so everyone knows what to look for.

What more can we do to stop this epidemic?

Link to comment
https://www.sau.com.au/forums/topic/18989-stolen-white-r33/#findComment-401276
Share on other sites

No alarm, no insurance...ouch.:rolleyes:

Irrespective of whether your friend gets the car back i think we should be passing the collection hat around. Please tell me he doesnt have finance on the car!

Does a Brant alarm make that big a difference to car security, say over another mid level aftermarket alarm.

Link to comment
https://www.sau.com.au/forums/topic/18989-stolen-white-r33/#findComment-402950
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
×
×
  • Create New...