Jump to content
SAU Community

Recommended Posts

Cheers for that sounds like i am running them a little to high then. Got to find a second a lap to give the GT2 a hurry up,

Will try that in the first practice tomorrow.

I want my slicks back, not likin these semi much now after not using them for 12 months :D

:D

Cheers for that sounds like i am running them a little to high then. Got to find a second a lap to give the GT2 a hurry up,

Will try that in the first practice tomorrow.

I want my slicks back, not likin these semi much now after not using them for 12 months :)

Ok thanks guys but its done and dusted now LOL

Got a first and a second placing against the GT2 in our 2 races so not to bad, got me by a half car length in the second race as my old girl pushed a little wide in third last turn....my fault not the old girl she did really well to be fair just need some good rubber under it and i will have him on a plate :P

going to try a dunlop DZ 02 i am told next time out see how they perform against the re 55. Anyone heard about them or used them. but thanks for the advice on the RE 55 i was at 36 and they were not good at all.

well done mate.

dz02 are about the same as the re55 (maybe a touch worse in the dry but better in the wet). But they have been superseeded by DZ03 which are better again. The DZ03 are the current tyre of choice among the tarmac rally guys

Thanks Duncan will post a few pic when they come through just for a few laughs.

Sorry i did mean to say DZ 03 was a typo was looking at them last night on the net, and while doing so i found these little numbers

http://www.tirerack.com/tires/tires.jsp?ti...odel=ECSTA+V710

what do you know about them if any as i had not heard of them before and i think as they are DOT legal i might be able to use them for the FIA GT3 racing week.

  • 4 weeks later...

That's the right site for the rim. No idea why it would do that, even when i hit 40psi hot at WInton the other week i just got lots of understeer, dropped the pressure for the next session and fine. No damage to the tyres.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The attached document is fine. I just downloaded & opened it.
    • Hello, sorry for being late to join the discussion, but my clock just died on me.   Ive tried to look at Michaels digital clock repair.docx and it doesnt work maybe the file has expired.   Please let me know if you can re upload it or take some youtube videos to show us how to get the clock installed? thanks
    • I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
×
×
  • Create New...