Jump to content
SAU Community

Recommended Posts

specs, spool rods, cp flat top pistons, around 8.1 . crank polished and balanced,oil restrictor fitted.one oil gallery blocked off, trust sump, n1 oil pump, oilreturn rear of head back to sump.etc

http://s212.photobucket.com/albums/cc220/rockabillyrb30/

Edited by rockabilly
oh wait up did you drop it in with the gear box still in the car??? i have a gts4 with a gtr gear box so i have the same crap to go through as you just have. how long did it take ya?

hi mate took me 4 hours from start to finish. had to drop the anti roll bar and power steering cooler, but that was because i have a trust sump extension. i lined the gearbox input shaft up with the clutch then with a jack dropped the gearbox mount down and slid the engine on,quite easy really.

Edited by rockabilly

yea im having all sorts of trouble with mine. first time ive ever done anything like this. and i seem to suck at it so far. when you say aligned the shaft with the clutch is there some sort of an extension tool that u can slide on the spline of the shaft an then stick the other end into the clutch? eeeergh... i just know in the morning when i wake up im going to be up for headaches. really need a second person to work the crane while ya line it up. how long was your car off the road? also it looks like you rebuilt that yourself?? i take it your a mechanic then?

hi mate,no hang the engine off the crane so it slopes slightly rearwards. then lower in and guide the front shaft of the gearbox into the clutch then lower it in. you need to lower the gearbox rear so its at the same angle as the engine. then lower the engine in so it lines up.as you lower push the engine onto the gearbox keeping it all lined up. no i am not a mechanic, but yes i did build mine myself.. bernie

hey man

there is such thing as a clutch alignment tool, the best tool i have ever made was when i cut the front shaft off the front of my Nissan Blue Bird gearbox which i would put in the clutch and slide into the spiggot bush then tighten the clutch and make sure the shaft can slip in and out easily then your set for putting the box in properly in the car, it has to be nearly 100% to slide in first go.

yea im having all sorts of trouble with mine. first time ive ever done anything like this. and i seem to suck at it so far. when you say aligned the shaft with the clutch is there some sort of an extension tool that u can slide on the spline of the shaft an then stick the other end into the clutch? eeeergh... i just know in the morning when i wake up im going to be up for headaches. really need a second person to work the crane while ya line it up. how long was your car off the road? also it looks like you rebuilt that yourself?? i take it your a mechanic then?

fired the old girl up today, no water in her just a quick 5 mins,went first time on the button, no oil leaks just a little raspy for me,could be the forgies being new and all, will see what it like when the water goes in and she runs longer,, oil pressure 100 psi on 20/50 asda special

just done a 10 mile drive in it. i tell you guys these motors are totally different to drive than a 26, and the sound from my exhaust is unbelievable. smooth aswell. i get positive boost on the avcr from 2000 rpm any gear. thats with a turbo rated to 700bhp. well chuffed. when its run in and opened up ,man it will go some.its trying to go now and its only done 11miles.lol

well its done 60 miles now on the crap 20/50 multigrade oil, been to 1.1 bar @ 5500 rpm on that oil. just dropped the oil and put some mineral 15/50,s in will run that for a hundred and fifty miles and that will be the run in done..probably gonna be jan 4 when it gets mapped as the tuners nearby are all fully booked and i cant have time off in dec.

Sounds ace. Very well presented and good luck.

Hopefully my rb25/30 will be finished and on the road before Christmas.

Just something i noticed:

You air pod/filter has a reducer cone, then you have a silicon hose attached to increase the size to match the intake pipe. Wouldn't you be better off to remove the pod reducer cone and fabricate another cone to match the pod diameter and the intake pipe. Just thinking you may be causing some minor restrictions with the current set-up.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
    • This is a recipe for disaster* Note: Disaster is relative. The thing that often gets lost in threads like this is what is considered acceptable poke and compromise between what one person considers 'good' looks and what someone else does. The quoted specs would sit absurdly outside the guards with the spacers mentioned and need  REALLY thin tyres and a LOT of camber AND rolling the guards to fit. Some people love this. Some people consider this a ruined car. One thing is for certain though, rolling the guards is pretty much mandatory for any 'good' fitment (of either variety). It is often the difference between any fitment remotely close to the guards. "Not to mention the rears were like a mm from hitting the coilovers." I have a question though - This spec is VERY close to what I was planning to buy relative to the inboard suspension - I have an offset measuring tool on the way to confirm it. When you say "like a mm" do you mean literally 1mm? Or 2mm? Cause that's enough clearance for me in the rear :p I actually found the more limiting factor ISNT the coilover but the actual suspension arms. Did you take a look at how close those were?
    • @GTSBoy yeah sorry i know thery are known for colors bud those DBA are too in colors 🙂 Green will be good enough for me  
    • That's my life. Past-Duncan has a lot to answer for
×
×
  • Create New...