Jump to content
SAU Community

Recommended Posts

ok.

Have a block and some forgies to whack in it. want some advice on getting the block prepped for some descent power (and boost)

Acid Dipped Block (clean all oil galleries and cooling jackets)

Bore/Hone

Deck head and block.

Double O Ring (Block and Head)

Copper Head Gasket

Crank ground - nitrided - and reground

Rods Shot peened and knife edged.

All reciprocating mass assembly (crank, rods, Pistons/rings, Flywheel (lightened billet)) Balanced and Blueprinted

New Gaskets all round.

What else is there to do? Planning to run big boost levels and a fairly big rev limit.

let us know.

I have the block, pistons and bottom end ready. ust finding out info on some of the toughening procedures that can be carried out.

thanks boys.

Mitch.

Also explain what it does etc.

Sounds the goods to me, just ensure that you use good rod/stud bolts etc if you are planning some decent rpm and boost. Same goes for bearings that you use.

If you are aiming at high RPM and power it may pay to speak to someone about the need for a better oil pump?

Good luck!

What bearings do people recommend?

Was thinking of just the ACL bearing kit...?

Oil pump eh?

might check it out. Would like to know some details relating to cooling properties with the speed of the coolant/water aswell. I have heard of pumping it too fast, doesn't get enuff time to cool etc.

Dunno.Time for some research me thinks.:(

Originally posted by Ballistic

ok.

Have a block and some forgies to whack in it. want some advice on getting the block prepped for some descent power (and boost)

Acid Dipped Block (clean all oil galleries and cooling jackets)

Bore/Hone

Deck head and block.

Double O Ring (Block and Head)

Copper Head Gasket

Crank ground - nitrided - and reground

Rods Shot peened and knife edged.

All reciprocating mass assembly (crank, rods, Pistons/rings, Flywheel (lightened billet)) Balanced and Blueprinted

New Gaskets all round.

What else is there to do? Planning to run big boost levels and a fairly big rev limit.

let us know.

I have the block, pistons and bottom end ready. ust finding out info on some of the toughening procedures that can be carried out.

thanks boys.

Mitch.

Also explain what it does etc.

Why are you going to O ring the block!? Copper head gasket? Jesus - do people still use and recommend such crap?!

Screw the standard rods - throw them in the bin and buy decent rods.

What are you planning to use for pistons?

What do you mean by "big boost"?

What is a "fairly big rev limit"?

How much money do you have to spend on this engine?

Mario.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
×
×
  • Create New...