Jump to content
SAU Community

Recommended Posts

im dieing to get a gtr front bar on my r34 sedan but will it fit straight on ...? if not what modifacations would i have to do???

sorry if this has been asked before.. im actually buying a kit very soon and need to know asap. and where would be the best place to get in... im located in melbourne.. and price????

thanks guys

cheers

should be able to put the gtr front end on take the blitz D1 car for example 4 door with gtr front end, you'd need the bonnet as well for sure but dont know about the guards (shouldnt have to change them), call up garage 13 they seemt o be the guys who know about these kits

should be able to put the gtr front end on take the blitz D1 car for example 4 door with gtr front end, you'd need the bonnet as well for sure but dont know about the guards (shouldnt have to change them), call up garage 13 they seemt o be the guys who know about these kits

Hmmm thanks bud .. Garage 13??? have yougot the number by any chance????

cheers

yeh not sure if garage 13 does them, just said to check out the website cause they seem to have alot of body conversion stuff, you should be able to use genuine parts i'd imagine like gtr bar gtr bonnet gtr lights (dunno if tehy're different from gtt) and get them from any jap wrecker that has the bit in stock

and yeh do it, looks hot

R34 GTR and GTT Xenon headlights are the same. To fit the GTR bar you will need GTR front guards, GTR bonnet, bonnet seal, bonnet hinges, bonnet latch.

would thgose head lights fit the R34 gt sedan???

On the other hand if you have deep pockets then pump them both.

haha man im so doing this... that looks hot... just gotta know what would be the best place to go in melbourne??????

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...