Jump to content
SAU Community

Recommended Posts

Guest Dakidmas

Hey guys,

I will be purchasing my first ever skyline but don't have a clue on what to look for in way of problem areas with these cars

(r33 gts-t), i am moving up from owning a silvia so i really don't know much in way of the engines on these things.

Any advice would be greatly appreciated, engine, body, interior ect. it all helps.

Thanks, Clint.

Link to comment
https://www.sau.com.au/forums/topic/19358-advice-on-r33s/
Share on other sites

Hey dude,

well problems i've had with my car are the book leaking on rainy days your boot can get pretty wet.. but some silicon fixed that, oh and if the car has standard shocks then its pretty common for the rear shocks to be rooted as well.. other than that the car has been pretty solid so far with no major problems, but then again i bought my car pretty much stock from japan i dont think my car had been thrashed everything is in top condition except for the shocks which just went after i was driving it though

Link to comment
https://www.sau.com.au/forums/topic/19358-advice-on-r33s/#findComment-406328
Share on other sites

I got this from a site, hope it helps you out a bit!!

(Sorry bout the large post though)

We are fairly lucky that we have a wide range of Skylines available thanks to our second-hand car importing industry which has been going strong for over a decade. With so many cars on the market, there is no reason to buy a lemon.

Here are some points to watch for with Skylines.

· The year of manufacture can be found by looking at the front seatbelts, near the floor mounting point. There is a fabric tag with the seatbelt specifications and the year of manufacture sewn onto the webbing.

· Inspect the welded seams in the front door sills just below the plastic kick plate. This is where I have seen rust start to form on Skylines, especially the R32. The R33 has an identical seam, so these will also show in years to come.

· Remove the rubber around the boot rim - this is a prime rust spot in any car. While you are in there, look in the side panels and make sure they are not full of water.

· Feel inside the panels in the boot where the jack is - debris found here will tell a story.

· Watch for glass (broken rear window or tail lights at some point)

· Inside the engine bay, look for crayon or chalk marks on components - this may indicate they have been replaced with second-hand parts.

· Crawl under the car and inspect behind the front and rear bumpers for signs of collusion damage.

· If you are keen, use a set of vernier callipers to measure the panel gaps especially on the doors.

· Mechanical - a noisy ceramic turbo isn't a good sign - see if it has been replaced with a conventional steel type.

· With the front wheels off the ground, check the play in the top end - any more than 5mm and there could be expensive repairs needed.

· Watch the oil pressure when the car is hot - Keep in mind the oil pressure sender is prone to failure.

After Purchase

· As you may not know the history of the car, it is best to start with a full service.

· Air filter - replace.

· Fuel filter - replace.

· Run a bottle of injector cleaner through the system with the next tank of petrol.

· Oil filter - replace, and change the oil. If there is a sludge problem do a hot oil change and repeat within 1,000 km. Don't use an engine flush treatment.

· Automatic transmission - have the oil changed. The transmission cooler should also be flushed.

· Spark plugs - replace. Make sure they are replaced with the platinum resister type.

· Timing belt - inspect and replace. Nissan specify a 100,000 km life for these. Be safe and prevent the rain of valves.

· Radiator - add plenty of anti-freeze. Without the protection of anti-freeze (corrosion inhibitor) there are parts that will corrode and eventually cause you grief. Check the condition of all the hoses while you are at it.

· Battery - monitor and replace if needed. Japanese car batteries are smaller than the regular sized car battery, and it may be the factory fitted battery (over five or six years old)

· ECU - reset it. Make it learn our driving conditions.

· Drive safe, respect the roads and enjoy the ride...

Link to comment
https://www.sau.com.au/forums/topic/19358-advice-on-r33s/#findComment-406342
Share on other sites

I got mine checked with the RAA, they did a 4 hr inspection on it.

They checked almost everything on it and gave a recommendation on if to buy or not.

It helped me out cause they saw stuff i didnt, and it cost $165.

Bargain if u ask me, saves the nightmares of gettin a lemon

HAPPY HUNTIN!

Link to comment
https://www.sau.com.au/forums/topic/19358-advice-on-r33s/#findComment-406344
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...