Jump to content
SAU Community

Recommended Posts

Guest Dakidmas

Hey guys,

I will be purchasing my first ever skyline but don't have a clue on what to look for in way of problem areas with these cars

(r33 gts-t), i am moving up from owning a silvia so i really don't know much in way of the engines on these things.

Any advice would be greatly appreciated, engine, body, interior ect. it all helps.

Thanks, Clint.

Link to comment
https://www.sau.com.au/forums/topic/19358-advice-on-r33s/
Share on other sites

Hey dude,

well problems i've had with my car are the book leaking on rainy days your boot can get pretty wet.. but some silicon fixed that, oh and if the car has standard shocks then its pretty common for the rear shocks to be rooted as well.. other than that the car has been pretty solid so far with no major problems, but then again i bought my car pretty much stock from japan i dont think my car had been thrashed everything is in top condition except for the shocks which just went after i was driving it though

Link to comment
https://www.sau.com.au/forums/topic/19358-advice-on-r33s/#findComment-406328
Share on other sites

I got this from a site, hope it helps you out a bit!!

(Sorry bout the large post though)

We are fairly lucky that we have a wide range of Skylines available thanks to our second-hand car importing industry which has been going strong for over a decade. With so many cars on the market, there is no reason to buy a lemon.

Here are some points to watch for with Skylines.

· The year of manufacture can be found by looking at the front seatbelts, near the floor mounting point. There is a fabric tag with the seatbelt specifications and the year of manufacture sewn onto the webbing.

· Inspect the welded seams in the front door sills just below the plastic kick plate. This is where I have seen rust start to form on Skylines, especially the R32. The R33 has an identical seam, so these will also show in years to come.

· Remove the rubber around the boot rim - this is a prime rust spot in any car. While you are in there, look in the side panels and make sure they are not full of water.

· Feel inside the panels in the boot where the jack is - debris found here will tell a story.

· Watch for glass (broken rear window or tail lights at some point)

· Inside the engine bay, look for crayon or chalk marks on components - this may indicate they have been replaced with second-hand parts.

· Crawl under the car and inspect behind the front and rear bumpers for signs of collusion damage.

· If you are keen, use a set of vernier callipers to measure the panel gaps especially on the doors.

· Mechanical - a noisy ceramic turbo isn't a good sign - see if it has been replaced with a conventional steel type.

· With the front wheels off the ground, check the play in the top end - any more than 5mm and there could be expensive repairs needed.

· Watch the oil pressure when the car is hot - Keep in mind the oil pressure sender is prone to failure.

After Purchase

· As you may not know the history of the car, it is best to start with a full service.

· Air filter - replace.

· Fuel filter - replace.

· Run a bottle of injector cleaner through the system with the next tank of petrol.

· Oil filter - replace, and change the oil. If there is a sludge problem do a hot oil change and repeat within 1,000 km. Don't use an engine flush treatment.

· Automatic transmission - have the oil changed. The transmission cooler should also be flushed.

· Spark plugs - replace. Make sure they are replaced with the platinum resister type.

· Timing belt - inspect and replace. Nissan specify a 100,000 km life for these. Be safe and prevent the rain of valves.

· Radiator - add plenty of anti-freeze. Without the protection of anti-freeze (corrosion inhibitor) there are parts that will corrode and eventually cause you grief. Check the condition of all the hoses while you are at it.

· Battery - monitor and replace if needed. Japanese car batteries are smaller than the regular sized car battery, and it may be the factory fitted battery (over five or six years old)

· ECU - reset it. Make it learn our driving conditions.

· Drive safe, respect the roads and enjoy the ride...

Link to comment
https://www.sau.com.au/forums/topic/19358-advice-on-r33s/#findComment-406342
Share on other sites

I got mine checked with the RAA, they did a 4 hr inspection on it.

They checked almost everything on it and gave a recommendation on if to buy or not.

It helped me out cause they saw stuff i didnt, and it cost $165.

Bargain if u ask me, saves the nightmares of gettin a lemon

HAPPY HUNTIN!

Link to comment
https://www.sau.com.au/forums/topic/19358-advice-on-r33s/#findComment-406344
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...