Jump to content
SAU Community

Recommended Posts

Okay I recently finished a build up of my car and have finally come to the turn key stage.

When I crank the engine I get all sorts of farts and blurps-Backfires etc but it wont run.

I had the crank/cam angle sensor off and I believe this is the problem as I have fuel and spark.

Now the problem is my CAS is not keyed so I have no idea where it should be?

Whats the easiest way to get it to the correct point before installation?

Do I just need to turn it a tooth and try again, and again etc.

Engine is an rb25det (I believe series 2) with standard internals.

Oh and when I pull the cas out and turn it the injectors pulse so Im sure its fine.

Im at my whits end I just want it running. I have searched and searched to no avail. :worship:

Thanks in advance.

Edited by calais25t
Link to comment
https://www.sau.com.au/forums/topic/193764-please-help-cas-problem/
Share on other sites

  calais25t said:
Do I just need to turn it a tooth and try again, and again etc.
Basically, yes. Although it must be close.

However you should be able to see the surface where the half-moon key broke from in the end of the exhaust shaft. Just use visualisation to determine which is the correct alignment.

Okay, so stupid question here,

Does one rotation of the CAS equal six injector pulses or does it need to rotate 6 times?

Is it possible Its injecting fuel into say cyl 3 and cyl 6 is the one that needs it? If you know what I mean..

What Im saying is could I be 3 or 4 rotations out or does it just work on one rotation. :)

  calais25t said:
Okay, so stupid question here,

Does one rotation of the CAS equal six injector pulses or does it need to rotate 6 times?

Is it possible Its injecting fuel into say cyl 3 and cyl 6 is the one that needs it? If you know what I mean..

What Im saying is could I be 3 or 4 rotations out or does it just work on one rotation. :wave:

yes one rotation is one cycle of the camshaft. and one rotation of the cas is two rotations of the crank.

  calais25t said:
There has to be an easy way to set the CAS. :(

i'm not sure if it will work out? but if you have access to a friends rb25det (R33) you could try it. set both the engines to TDC. on the other engine/car pop the lid on the cas so you can see the rotor plate. then pop your lid, match it up, then put it back on.

might be a bit of a stuff around but it sounds like your fed up with it. also what DEAD32 said, if your continually cranking your car and not sparking, you plugs with fowl up and worst case your sump starts filling with fuel. not nice.

The teeth that mesh between the CAS and the cam are quite coarse. You have to turn the CAS shaft a fair bit to get it to align in the next set of teeth.

As I said previously, use a bit of visualisation to work out where the key in the CAS has to be to align with the "key" in the exhaust cam.

Okay, Im sure the CAS is in the right position and the F&*%ER will not start...

Ive pulled the plugs and checked and they are sparking well.

Its getting fuel and the injectors are working.

My computor runs a map sensor so basically it cant be anything such as AFM or the TPS caus eit dosent have one.

Is there anything else here it could be its got me baffled?

what ecu? what diagnostics does it have?

have you checked the basic sensors

- afm or map

- water temp

- cas

do you have spark? use a screwdriver tapped onto the engine block & try to crank it

do you have fuel? undo the fuel line and see if you have fuel coming out

do you have air? check the air inlet / afm or map sensor

lastly with whatever ecu you are check some of the basic sensors

even the std ecu has built in diagnostics to debug why it wont start

yes, what ecu are you running? i just looked back to your first post and you say that you have fuel and spark, if the cas was faulty you would have these. how did you check for fuel and spark?

on some aftermarket ecu's you have to tell the ecu your firing order for it to work. also whats you battery voltage like? if its low your coils may not be charging properly giving you a weak spark.

Edited by QWK32
  QWK32 said:
yes, what ecu are you running? i just looked back to your first post and you say that you have fuel and spark, if the cas was faulty you would have these. how did you check for fuel and spark?

on some aftermarket ecu's you have to tell the ecu your firing order for it to work. also whats you battery voltage like? if its low your coils may not be charging properly giving you a weak spark.

Its an EMS stinger ECU.

It was perfectly tuned about 2 years ago when I took the car off the road, and as far as I know none of the settings should have changed.

To test spark I rotated the CAS and watched the spark plugs fire.

I can also hear the Injectors ticking and my fuel pressure gauge is reading 30psi of fuel pressure.

  calais25t said:
On the last atempt I got a 6 inch flame out the throttle body.

that tells me that the cas isn't lined up properly. or you cams are out. have you checked that your timing marks on the cam pulleys all line up.

i know its probably unlikely, but is there anyway the ecu has been reset?

  QWK32 said:
that tells me that the cas isn't lined up properly. or you cams are out. have you checked that your timing marks on the cam pulleys all line up.

i know its probably unlikely, but is there anyway the ecu has been reset?

I havent touched the cams or the timing belt since it last ran.

The compuor still has the maps when I plug it into the laptop.

Im ready to set it on fire.....

Is the series 1 and series 2 CAS the same????

  calais25t said:
Is the series 1 and series 2 CAS the same????

from what i understand the are, except the very late model 33's have one the same as a 34.

still running stock coilpacks?

what you could try is: (just to check everything)

unplug the injector harness from the main plug at the front so as not to inject fuel. pull the coilpacks out and place them where you can see them spark. manually rotate the cas and check that the firing order goes in the sequence of 1 5 3 6 2 4. you may not get that a first depending on your current cas position, it may start from 3, etc.

if thats all good, then set the engine to cyl 1 at TDC. with the cas held the right way up, rotate the cas till coil 1 fires, then turn it around a very tiny bit more. that'll be where the right cas tooth alignment to the cam is, then put that onto cam and set the cas bolts so they are about halfway in the slotted holes. this will be a good spot to start till it gets running and you can get a light on it.

then plug the injector harness back in. make sure they are plugged in the right way, and getting a signal. and your fuel lines are the right way around.

if thats all good the only things left are your MAP sensor, and ecu settings.

  QWK32 said:
from what i understand the are, except the very late model 33's have one the same as a 34.

still running stock coilpacks?

what you could try is: (just to check everything)

unplug the injector harness from the main plug at the front so as not to inject fuel. pull the coilpacks out and place them where you can see them spark. manually rotate the cas and check that the firing order goes in the sequence of 1 5 3 6 2 4. you may not get that a first depending on your current cas position, it may start from 3, etc.

if thats all good, then set the engine to cyl 1 at TDC. with the cas held the right way up, rotate the cas till coil 1 fires, then turn it around a very tiny bit more. that'll be where the right cas tooth alignment to the cam is, then put that onto cam and set the cas bolts so they are about halfway in the slotted holes. this will be a good spot to start till it gets running and you can get a light on it.

then plug the injector harness back in. make sure they are plugged in the right way, and getting a signal. and your fuel lines are the right way around.

if thats all good the only things left are your MAP sensor, and ecu settings.

I did try that but the problem is Im getting multiple sparks at the same time. Im sure the computor uses a wasted spark setup which makes it hard.

The other thing is it seems like the sparking is random depending on how fast I spin the CAS.

How do I know which stroke the number one piston is on ie intake or exhaust?

I tried unplugging the fuel line both into the rail and the return from the regulator and they both flowed a cup fuel in a couple of seconds but the pressure didnt seem massive, how much should there be?

Everytime I try and start it now, I pretty much get nothing followed by massive backfires I mean BIG.

One thing is I dont have the intake pipe on so its sucking straight into the throttle body although I cant see that making a difference.

Here how I set my CAS up.

Removed #1 coilpack and put dummy spark plug in it to check spark.

Line TDC up on the crank with the marker (the red stripe on the pulley)

Remove CAS and turn the shaft with the ignition on, until the dummy spark plug fires. Make sure the plug is grounded.

Now without turning the CAS put it back in the motor. If it still doesnt start and backfires, then the #1 piston is 360 out.

Get the motor to TDC again on the crank pulley. Turn the engine over EXACTLY 360 degrees (1 turn). Refit CAS there and try again.

This will get the CAS close enough to start the engine and fine tune it from there.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
×
×
  • Create New...