Jump to content
SAU Community

Recommended Posts

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

sorry i did mean i dont use the turbo timer countdown part of it :( i use all the other features tho!

i kniow

i like the other features it has

however i will use the timer too

plus it looks sleek and sexy

to be honest, i can't see anyone monitoring AFRs, voltage, etc. they're factors you can hardly control - let alone requiring any attention.

the only thing i keep an eye on is my knock sensor (safc) and even then only racing.

oil temp, oil pressure & water temp - the basic three you'll need.

sleek and sexy? it's a plastic box :(

i want to get a safc but there is no point when i will be getting an aftermarket ecu, so cause i wanted to get a couple of gauges (air/fuel and voltage) it was gonna cost me 600 bucks for the gauges and to get them installed, when i saw the apexi auto timer, it had everything i needed, and for a much less cost factor, thats why i got it :(

i guess cause my car has gone rich a few times for god knows what reason i like to keep my eye on the a/f ratio.

i do agree eug, that in the end its not something i can control

running rich is fine, cars do it all the time.

often ecu's often put more fuel in as a safety to running too lean (which is bad). i.e. cold start, etc.

well yes there's my point - if your car runs rich/lean for a few seconds, are you going to get off the throttle, pull over and turn the car off?? the ecu (and/or piggyback) if working should be controlling all of that anyway.

gauges are for monitoring when racing, when cars are put under extreme conditions - apart from that it's just a wank thing i suppose.

it is a show car no, so that's kinda the point?

i'm not making fun.

i mean wank is such a loosely used term. something you have, but don't really need - just exactly what the original poster said; the kinda stuff to show off.

ahh lol i have an apexi turbo timer for NA and turbo i was going to fitt it when my car was NA but now i defintatly going to fit it now itz turbz, cant hurt to have one on an NA all cars need to be cooled down, however it can be pointless...read wat EUG has said!

I dont see the point of turbo timers..

If you know your approaching your destination.. just take it easy 2 or 3 min before you get there.. just like you do when you start the car on cold mornings..

Give the car 30 sec or so while you gather the things you need from your car.. THEN switch it off..

Honestly.. unless your doing track work.. and your car is working at high temps.. then dont bother.. even then.. your at a track.. leave the engine on.. its not like somone is gonna steal it..

Its not like there is so much engine wear due to turning the engine off when warm that it justifies having one..

its called a TURBO timer for a reason.. it allows a TURBO to cool down as they can spin at 50,000 RPM and they do need lubrication as they cool down.. thats why the engine is on to allow the turbo to spin at much slower rpm while being lubricated and cooled..

but i could be wrong..

its all good, it came in handy at gazzanats, especially cause i asked so much from the car doing the go to whoa, i mean i really needed her to go, so i kinda put my foot down hard a few times and in the end she did well. everything held together which is the main thing

i intend to do more events like the go to whoa, dash for cash etc, so the timer countdown will come in handy,

its all good, it came in handy at gazzanats, especially cause i asked so much from the car doing the go to whoa, i mean i really needed her to go, so i kinda put my foot down hard a few times and in the end she did well. everything held together which is the main thing

i intend to do more events like the go to whoa, dash for cash etc, so the timer countdown will come in handy,

:(:P:):spank:

what are these events?

I dont see the point of turbo timers..

If you know your approaching your destination.. just take it easy 2 or 3 min before you get there.. just like you do when you start the car on cold mornings..

Give the car 30 sec or so while you gather the things you need from your car.. THEN switch it off..

Honestly.. unless your doing track work.. and your car is working at high temps.. then dont bother.. even then.. your at a track.. leave the engine on.. its not like somone is gonna steal it..

Its not like there is so much engine wear due to turning the engine off when warm that it justifies having one..

its called a TURBO timer for a reason.. it allows a TURBO to cool down as they can spin at 50,000 RPM and they do need lubrication as they cool down.. thats why the engine is on to allow the turbo to spin at much slower rpm while being lubricated and cooled..

but i could be wrong..

That is the perfect definition of what a turbo does, you are correct!! and thats why its called a TURBO TIMER, however like i said above cant do any damage to the car, so if u want one on an NA why not? apart from looking slightly wierd and eating more fuel...

hame

That is the perfect definition of what a turbo does, you are correct!! and thats why its called a TURBO TIMER, however like i said above cant do any damage to the car, so if u want one on an NA why not? apart from looking slightly wierd and eating more fuel...

hame

I just dont see a real use for it on an NA..

Its just another thing that im spending money on.. money which I can spend on other things..

Another thing that the car could get broken into for..

Another thing that can break and root around with other things..

Another thing that can cause problems..

Im spending petrol for no real reason.. and petrol is only gonna get more expensive.. :(

but thats just my 2 cents..

Cris makes the point exactly, the point of a turbo timer is for the actual turbo and oil to cool down, not the motor.

The motor uses the radiator to cool down - which requires air flow, so having the car sit stationary whilst cooling down isn't really a good thing. When racing, i normally do 1 warm up lap, 3-4 hot laps, 1 cool down lap, cruise into pit bay and switch her off. Far more stressful than a 20 second straight line run.

edit: having your car on idle wears bearings and other components faster

read anywhere in any manual and you'll always find that excessive idleing is bad for a car be it hot or cold, letting it warm up a little is good but you still only warm up the engine its best to just cruise for a little while to warm up all moving parts ie engine, trans and diff. warm down is nessecary for track work and high speed runs or excessive thrashing but as eug says the engine cools down via the coolant and the only way to cool down coolant is air flow and moving air threw the radiator is much more effictive way then making the fan's doing the job, also the fans dont kick in untill a certain tempreture so if your below that temp letting the car idle will only increase the engine temp not reduce it

Turbo timers are designed for the turbo to cool down and now they are primarly desiged for OIL only cooled turbos to cool down, the way the stock oil heat exchangers work they do not need air flow to cool the oil to the desired tempriture and flow is the best way to cool the turbo and let it spin down from 50,000 ish rpm to idel rpm, but these days the turbos are lubricated with oil and cooled with coolant (most good turbos that is, cheapies still run primitive systems) and the only way to cool coolant is air flow threw the radiator. and as eug said excessive idleing is ment to induce premature bearing wear, turbo timers are the biggest wank factor if they were really so good and nessacary they would be a stock item on stock turbo or na cars, yet name me a car which has one from factory??

As for the a/f ratio cara and anyone else, the stock oxy sensor doesnt run a wideband sensor and is only really good enough with keeping emissions down, and is no way neer good enough to determine if the car is running lead stoich or rich, you need a proper sensor which runs more than 1 volt to determine the actual reason, even the after market a/f ratio gauges are pointless without the right sensor to back it up.

PS sorry about the essay and the spelling mistakes lots of beer make me slir my typing

thank god we have people with some form of knowledge around here... despite your intake of -OH fluids you hit the nail on the head.

in summary; a turbo timer is probably doing more negative than positive on an NA car ;) and i'll re-iterate - wank.

go the greddy turbo timer....u get spd, rev count, 0-100k, 0-400m etc etc - good for the track and what not

You have a tacho for speed..

A tacho for your revs

why?.. its slow..

You get a slip at the end of the drag strip..

:(:domokun::blush::blush:

what are these events?

the go to whoa is where u start on a line, and have to go as fast as you can to another line, about 100 or so metres long, and your front tires have to stop on the other line.........if that makes sense

the dash for cash is like a mini obstacle course where u basically have to go as fast as you can, without mucking up, as there is a certain way you have to go around the course,and the lowest time wins

You have a tacho for speed..

A tacho for your revs

why?.. its slow..

You get a slip at the end of the drag strip..

its teh multifunctional :domokun:

and it glows blue :(

plus its got other goodies - and quite good for the price...only 120 or so

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I had 3 counts over the last couple of weeks once where i got stranded at a jdm paint yard booking in some work. 2nd time was moving the car into the drive way for the inspection and the 3rd was during the inspection for the co2 leak test. Fix: 1st, car off for a hour and half disconnected battery 10mins 4th try car started 2nd, 5th try started 3rd, countless time starting disconnected battery dude was under the hood listening to the starting sequence fuel pump ect.   
    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...