Jump to content
SAU Community

Recommended Posts

not sure that was what Chris had in mind...

If you want to see those cars in recent competition, I suggest you should all go and look at some photographs of that I captured of both of those cars.

You can see the Black 35GTR here at my photo album.

_SJT6729-Targa09Winner996TonyQuinnN.jpg

Edited by Stephen Thorpe
  • 1 month later...
yep, i agree lets see what you got.

Hi, again.. I was abroad and have problems with internet access. So, i'm reverse engineer and specialized on mobile platforms (e.g. translating phones). I have experience in reversing&translating area (for example i was the first in ussr area who translated some well-known brand phone to russian lang). That's why I want to work with you. 

Sweet :)

I would give you $100 for a CD/DVD that would translate the menus from Jap to Eng.

I'm sure everyone would give you $100 for the Translation.

The whip is out lets see some progress ;)

Well, can someone send me some existing CD/DVD with firmware, or dump, or something else. Also I want to know popular models and so on... In short, I want have all info regarding your devices :cheers:. Plz, email me - z3rr0w at gmail.com

Best regards...

true....

DVD is probably easier to do, as long as the person has a dual layer burner... which should be pretty common these days.

the problem is the firmware. no one here I think can do that without actually sending the whole DVD ROM drive unit to you (the actual hardware).

and doing so means the person taking off the DVD ROM will loose all AV on the factory nav screen... because that thing is the 'brain' that controls

the whole navigation and trip computer.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
    • I just stack 2 pieces of 200x50 timber on top of each other. Total length about 900mm, with the top one being a little shorter and both having a 45° angle cut on them to make the front edge a bit of a ramp. Put these in front of each front wheel, drive up on them, throw the trolley jack under. Takes 1 minute. Scissor jacks can eat a bowl of dicks. I never use on under my car unless desperate.
×
×
  • Create New...