Jump to content
SAU Community

R32 Gtst - Anyone Installed Hid To These?

applion

By applion,
in Exterior & Interior Styling

 Share

Recommended Posts

subie Grand Master

subie

Posted
Posted
As was said GTST type m/GTR are H3C GTST pov pack H1 same as na and N1 lights.

Speak to slide he has plug and play kit got a set in mine

What have u got on ur car? H3C or H1?

if it H1, are they HID kit that U bought from Slide? how was it in term of installation?

Cheers

dmac_25 Grand Master

dmac_25

Posted
Posted
What have u got on ur car? H3C or H1?

if it H1, are they HID kit that U bought from Slide? how was it in term of installation?

Cheers

H3c easy the hardest thing is finding a place to mount the resistor pack.

the H1 should be the same plug and play

Dahtone Racing Grand Master

Dahtone Racing

Posted
Posted

you obviously cant see why its no kit will be plug and play, not even slides ones unless he has some super special bulbs with clips built in

there is nothing to hold the blub in the head light

thats what the socket in the pic does

Dahtone Racing Grand Master

Dahtone Racing

Posted
Posted (edited)

just took some pics now

first two pics are of the old holder after i chopped it up, its used to hold the new HID bulb in

2438716952_7224ec5c39_o.jpg

2437894795_97d865cf6b_o.jpg

last pic is of the spacer

2437894863_0b2752333e_o.jpg

everything fits nicely and all works perfectly

when i fit these to customer cars the spacer is one peice with the clip

so all that has to be done is put the bulb in and push the new clip in

Edited by Dahtone_Racing
adam-__- Grand Master

adam-__-

Posted
Posted
thanks dahtone, did mine yesterday!

Anyone know how to keep low and high beams on together?

Cant seem to find a thread on it.

There's a tutorial in the DIY/Tutorial section. I'll grab it for you when/if I go by it.

  • 6 months later...
nIsMo86 Experienced

nIsMo86

Posted
Posted

I have the H1's and i used round bodykit fitment tape. Took out H1 holder, put globe through hole in middle of bodykit tape, push into headlight housing. Too easy.

Mine have been installed like this since around march this year.

Another option i guess. I do like dahtone's idea better though mine hasnt failed either.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • PranK
      Chris' Toyota Mark ii JZX110

      By PranK · Posted

      This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
×
×
  • Create New...