Jump to content
SAU Community

Recommended Posts

My clutch went on friday night, and i couldnt get it up the drive way therefore i had to leave it sitting outside my house. I already have an alarm system, but being the paranoid person i up, i put the steering lock on, took a few fuses out, disconnect battery, unhook few parts to the car - all this while bearing in mind my clutch was gone and they no one could drive it.

Monday morning (the day which my car was goin into the workshop to get clutch fixed) (whom i believe tried to tax my car) decided it aint going anywhere and eventually screwedit up. THey glued AND body filled parts of my car, the door, keyhole, windscreen water shooter thingy, my windscreen and bonnet - WHY! Why i ask myself, THey could have stole my brand new headunit which i put it, would have made me feel happier. But their $10 glue and body fill gonna set me back about $1000 (which i do not fcukin have). THey made a mixture which solidfy really quick, they knew what they were doin. I thought my suburb was safe, which i guess it aint no more. A SUnday night on a school holiday - sigh* not happy, very depressed.

Guess this is my string of bad luck, first the clutch then the vandalism - HAS THIS HAPPEN TO ANYONE before, how do i get the stuff off without wrecking, scratching the paint, I've gotten about 40% of the putty off, but it still really really suck. I Would love to pole some little shits, I'm 18 years old myself - and work my ass 3 years for my ride, one month after i purchase my car little someone does this. 2 days not garaging my car this happens. Anyone can help me get this stuff off??

Okay, my rant is over

bryanlee38

  • Replies 73
  • Created
  • Last Reply

Top Posters In This Topic

Thats harsh man.. Sorry to see that.. Makes me cry to see that kinda treatment to such a beautiful car.. I hope you catch the little turds and phuck em up...

maybe get a mate to put his car in the same place.. and camp out all night? Big of vigilante mayhem always makes the grass that little bit greener...

Guest Boxhead

and who says hiring pedofiles is a bad thing...

i rekon we should take them to kinsg kross in sydney, or nerang up here, either one works.. duct tape the little shits to a pole naked.. so there little assholes get raped...

sorry to hear it bryanlee... but if you have any suspects just start hitting them till they either admit to it or tell you who it was.

It's like my bad luck - Bought my car, and 3 days later a piston phucks up on me.. I mean fair enough I was going extremely fast.. but still I know how ya feel bro...

Maybe we should start a club of people who have Skylines with really bad luck.. Kinda like a support group? :D

everyone has had bad luck sooner or later with their cars.. first month i ownded my car a truck decided he wanted my lane and drove me into the gutter.

2 x ASA LS1 Wheels @ $550 each and 2 tyres over $250 each.

geez bryan! that sux! can you get prints from the putty? i hope you get them! noticed you got a new headunit too. so i guess you wont be needing mine right? good luck findin them mate!

I left my old car at the front of my house (which was normally locked in the garage) last year and some f**kers broke all the windows. I had like $50 in the ashtray a $3000 sound system and they did not take anything! Just needless violence against our rides little sh!ts... I feel your pain, bryanlee38, if they did it to my Skyline there would be hell to pay...

What really bugs me is its the people like bryanlee38 who really care for their cars and take such great lengths to prevent it getting stolen etc, leave the car outside for only a few days and the little bastards do that to it. It seems the people who don’t care for their similarly attractive cars in the same way and park them wherever go without any problems, funny how it works. Not to say something like this should happen to those others either but just sad to see this happen to someone who worked so hard for the car. Remember what goes around comes around.

One Thing bryanlee38.. on the forums has anyone been asking lots of questions about where you live or anything about your car? Maybe it was someone who logged on here looking to hurt someone? Not implying anything.. just tossin you ideas to maybe track down the purps...

and I agree with predator.. they'd have to be local.. Noticed anyone around your area giving you dirty looks for driving that car in a certain area? maybe showing it off at any local supermarkets? (and don't say you aint proud and havn't shown it off) :D

Once again.. just throwing ideas your way.. Tryin to help..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...