Jump to content
SAU Community

Recommended Posts

Hi All,

Cleaning out my garage, got some stuff for sale. I'm located in Tasmania but will post the smaller items if need be

Item: Standard RB20det turbo

Condition: Excellent! very very minimal shaft play

Price: 200 ono 150 bucks

To Fit: T3 flange

Location:

Contact: PM or Post here

Comments: Was on my car a few months ago, only taken off due to upgrade

P1000533.jpg

Item: Standard RB20det injectors

Condition: Only took out of the car last week...works perfectly, seals in great condition

Price: $100

To Fit: Rb20det

Location:

Contact: PM or Post here

Comments:

injectors.jpg

Item: 3inch catback exhaust

Condition: excellent

Price: $100

To Fit: r32 skyline

Location:

Contact: PM or Post here

Comments: No rear muffler, has a flange at the end to bolt on cannon or whatever. has a mid muffler

P1000531.jpg

Item: 4 x sparco 16inch wheels with 2 roadworthy tyres

Condition: good

Price: $300 250ono

To Fit: skyline or anything 5 x 114.3

Location:

Contact: PM or Post here

Comments:

P1000535.jpg

P1000536.jpg

Edited by TazzS13
Link to comment
https://www.sau.com.au/forums/topic/194805-heavys-garage-sale/
Share on other sites

  • 4 weeks later...
  • 3 weeks later...
  • 4 weeks later...
there is a pic of the wheels in the thread man

sorry mate they didnt cum up they have now so were bouts you located?? iam of to melbourne 4 3 weeks on a holiday if you still have them wen i get bak i will take em of your hands

Edited by bwebbie1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...