Jump to content
SAU Community

Fully Built Greddy Sr20det ***cams To Sell***

STATUS
 Share

Recommended Posts

STATUS Grand Master

STATUS

Posted
Posted

S13 SR20DET COMPLETE ROCKER COVER TO SUMP ENGINE (COMES WITH ALTERNATOR, STARTER AND ENGINE LOOM, INJECTORS NOT INC), THIS ENGINE WAS BUILT AS A NO-EXPENSE SPARED EXERCISE AND SHOULD HANDLE JUST ABOUT ANYTHING., WITH A SMALL TRUST TD06S L2-20G TURBO KIT MADE A LAZY 279RWKW @ 1.3BAR WITH A LARGER TURBO HIGH 300RWKW WILL BE NO ISSUE.

Engine Specs:

JUST SOME OF THE PARTS USED….. TOTAL BILL WAS OVER 12K!!!

GREDDY PISTONS 13525802 $1559

GREDDY H-BEAM RODS 13525401 $2499

CARILLO ROD BOLTS

ARP MAINS $189

ARP HEAD STUDS $249

GREDDY HEAD GASKET 13521328 $329

GREDDY VALVE SPRINGS 13523801 $329

GREDDY STEP 2 CAM 264 11.5 13525209 $499

GREDDY STEP 2 CAM 272 11.5 13525210 $499

GREDDY CAM GEARS X2 13523303 $469

GREDDY SUMP 13525901 $549

GREDDY ROCKER STOPPERS 11522050 $139

ACL RACE BEARINGS

FULL MACHINE WORK

FULL HEAD RECO

FOR THOSE WHO WISH TO USE IT AS A COMP ENGINE I WILL ALSO INCLUDE ALL THE MODIFIED COOLING SYSTEM COMPONENTS, IT HAS ALL THE MANIFOLD AND HEATER LINES WELDED UP AND IS DESIGNED TO RUN WITH A REMOTE HEADER/SWIRLPOT. THIS ELIMINATES ALL HOSES EXCEPT FOR UPPER AND LOWER RAD HOSES. THESE COMPONENTS ARE ALL BOLTS ONS AND CAN BE REMOVED TO FIT THE STD PARTS IF YOU WISH.

FULL MACHINING WORK, DONE TO A VIRGIN BLOCK. TORQUE PLATE HONED, DECKED, LINE BORED,

HEAD FULLY RECONDITIONED, NEW LIFTERS, VALVES, VALVE SEATS AND GUIDES.

THIS ENGINE HAS DONE 5 MEETINGS AND IS AS NEW, IT WAS STRIPPED FOR INSPECTION AND HAS HAD A BRAND NEW 1.2MM HEADGASKET INSTALLED. THE ONLY REASON THIS IS FOR SALE IS THE CAR HAD A RB26DETT TRANSPLANT. CAR RAN ONLY THE BEST ENGINE OIL AND WAS CHANGED EVERY MEETING.

$6000 ono

have a set of cams to sell see link: http://www.skylinesaustralia.com/forums/Ch...ml#entry3548334

post-34927-1196048399_thumb.jpg

post-34927-1196048584_thumb.jpg

STATUS Grand Master

STATUS

Posted
  • Author
Posted
put it back in lol

nah the 26 is sorted now, the T517Z's where too linear and responsive, cut killer laps but hated drift. not agressive enough but hey. This time i get to build what i want for the 26 much like i did for this SR ...not what im asked to build :P responsive lazy power was the ask but agressive is the only way ;)

(i actually built 3, 2 for mates and one for cats car but cats had differrent rods and cams)... you being a ns.com poster would know the other two cars the engines went into.... 180athid and godhand.

STATUS Grand Master

STATUS

Posted
  • Author
Posted
I don't see a price between all that yelling ;)

i baldy locks'ed it for you :P

http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi....cSELL.m315.lVI

STATUS Grand Master

STATUS

Posted
  • Author
Posted
goodluck with the sale trent this engine is a machine, same with athids engine. im sure your rb26 will be a monster aswell :P

cheers, hows yours coming along?

den001 Proficient

den001

Posted
Posted

considering whats in the engine thats as cheap as u will find a proper built sr20...

go buy carillo rods and see what they set u back on their own... then u will appreciate this price.

good buy mate, good luck

STATUS Grand Master

STATUS

Posted
  • Author
Posted
hmmm i wish, but i dont think i want fork out that kind of money......

good luck with the sale

ps your car is the shit, best 32 in vic.

W0rp3D Grand Master

W0rp3D

Posted
Posted
hahaha some jerk offered 1500..... i rather piss on it than sell it for that :nyaanyaa:

"Tell him his dreamin"

Am i wrong is that the drift cats car?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...