Jump to content
SAU Community

At A Dead End

Adz2332

By Adz2332,
in Exterior & Interior Styling

 Share

Recommended Posts

Adz2332 Grand Master

Adz2332

Posted
Posted

Hey all,

Im chasing The side skirts and rear bar from the Bee*R R34 onto a R33 converstion kit.

I have tried everyone and anyone i can think of here in aus.

I found Bee*Rs website and emailed them but had no reply, wouldnt be suprised if they couldnt read the english! lol.

So now im wondering if anyone can suggest any one in japan or has anything to do wid japan an exporting to see what they can do from there.

Have run into dead ends in all that i have tried and dont know where to go from here.... :w00t:

Link to comment
https://www.sau.com.au/forums/topic/195354-at-a-dead-end/
Share on other sites
adam-__- Grand Master

adam-__-

Posted
Posted

You probably didn't get a reply from the shops because most of them don't want to send over seas or because they didn't understand the email like you said.

You could always try the traders on here and ns.com about getting them in for you. Ask them if their 'people' can source the parts you're after. Worth a try, better than nothing right?

Link to comment
https://www.sau.com.au/forums/topic/195354-at-a-dead-end/#findComment-3500482
Share on other sites
Adz2332 Grand Master

Adz2332

Posted
  • Author
Posted
You probably didn't get a reply from the shops because most of them don't want to send over seas or because they didn't understand the email like you said.

You could always try the traders on here and ns.com about getting them in for you. Ask them if their 'people' can source the parts you're after. Worth a try, better than nothing right?

cheers havent tried NS.com yet ill head over there now

Link to comment
https://www.sau.com.au/forums/topic/195354-at-a-dead-end/#findComment-3501457
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • PranK
      My new to me M35 Stagea wagon

      By PranK · Posted

      Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Chupapy
      New r33 owner

      By Chupapy · Posted

      Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...