Jump to content
SAU Community

Recommended Posts

Hey all,

Im looking at buying some front vented gaurds that are 30mm wider than the standered ones. So im guessing my wheels now wont fill out the gaurds...

So i may look at some new wheels. What offsets and width should i be looking for?

What sort should i be looking at to fill out the gaurds more now... Want some dish... and under or around $2000...

Any help would be great..

Also looking at some rear over fenders... but how are these held on?? am looking to try and do it myself... ideas?

Edited by Adz2332
Link to comment
https://www.sau.com.au/forums/topic/195544-filling-out-the-gaurds/
Share on other sites

we usually grind the rear quarter back to metal, then use 3M Automix to adhere the fibreglass directly with the exposed metal... reinforce by drilling and resining through so that the overfender doesn't move around and cause hairline cracks in the paint a couple of years down the track. If the fender allows for it we may pop rivet as well for additional reinforcement, but not where the rivet has to be covered by filler to hide it, as a couple of years down the track the filler tends to shrink around the rivets and show dimples.

3M Website for Automix

we usually grind the rear quarter back to metal, then use 3M Automix to adhere the fibreglass directly with the exposed metal... reinforce by drilling and resining through so that the overfender doesn't move around and cause hairline cracks in the paint a couple of years down the track. If the fender allows for it we may pop rivet as well for additional reinforcement, but not where the rivet has to be covered by filler to hide it, as a couple of years down the track the filler tends to shrink around the rivets and show dimples.

3M Website for Automix

He's reffering to Front vented guards (replacement) not rear guards.

As for the front guards, it says 30mm wider, but they actually taper back into the door and the front bumper, so they are only 30mm wider at the middle of the guard then meet back to the factory bumper mounting points, its abit hard to explain, but when i had these guards on my r33, i could only space them out a extra 20mm or so, before rubbing. As for offset around +20 should do.. If using a bolt on spacer, go for the minimum size of 25mm, you should be fine, aslong as the car isn't overly low.

ahhhh pop riviting to the car.. hmmm no way you can do it without damaging panels??

Most people use this technique because it's cheap and it gives that 'tough' look to the car, but I don't think it's the look you're after.

He's reffering to Front vented guards (replacement) not rear guards.

As for the front guards, it says 30mm wider, but they actually taper back into the door and the front bumper, so they are only 30mm wider at the middle of the guard then meet back to the factory bumper mounting points, its abit hard to explain, but when i had these guards on my r33, i could only space them out a extra 20mm or so, before rubbing. As for offset around +20 should do.. If using a bolt on spacer, go for the minimum size of 25mm, you should be fine, aslong as the car isn't overly low.

+20? i reckon you could get away with lower than that

i had 17x8" +32 on the front of my r33, and it wasnt flush with the guards, so if you are putting on another 20-30 mm, you should be able to sneak in a gtr-ish offset rim, like +12, even if you have to add a degree of camber :)

that said, it depends on what widths you want as well..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...