Jump to content
SAU Community

Recommended Posts

Cost: $25 for driver or passenger

Time:

Gates open at 8.00am

Scrutineering commences at 8.15am.

A compulsory Driver’s Briefing is held at 9.30am

Activities on the Track commence at 10.00am

Info:

Speed Restriction – all drivers will be limited to 80% of the potential of both the car and driver.

This is not a race . There will be large differences between the speed of each vehicle so be careful. Anyone exceeding the 80% rule or overdriving will be flagged off the track and warned. A second offence will mean that it is home-time for you.

Scrutineering - All cars must have a safety check and receive an ‘OK’ sticker before going onto the circuit for the first time. Vehicles must be roadworthy or race worthy.

Brake lights must work.

Clothing – must be non-flammable cotton or, preferably, wool – no nylon – covering wrist to neck to ankles. Proper enclosed footwear – non flammable. No thongs or sandals.

All participants must wear a helmet which complies with current Australian Standard.

Noise – All vehicles must have an effective muffler fitted to the vehicles exhaust system in a manner which will reduce the engine noise. Maximum noise level permitted is 95dBA

Sessions - activities will be conducted in session of 30 minutes Driver only, followed by 30 minute session for driver and passenger. Sessions maybe shorter than 30 minutes, depending on track problems with cars etc.

Seatbelts must be worn at all times. Done up tightly.

Other cars - Be careful of other cars, watch out for them and give clear hand signals if you are going to slow down. Pull off and brake early when safe to do so. Do not brake suddenly when cars are following close behind. If you need to slow down, give hand signal and pull out of the way of others.

Age Restrictions - An opportunity for people over 16 years old to drive around the circuit under controlled conditions. Children must be at least 14 years old to be passengers. It is not a day for young people to learn to drive a car.

Contact Winton for more information - 5766 4235

Link to comment
https://www.sau.com.au/forums/topic/196381-winton-fun-day-sun-16-dec/
Share on other sites

dont worry about the noise level.

my r31 is at 130db @ 4000rpm and they haven't kicked me off yet.

and with the 80% rule thier is userly a few cars (apx 30 or so) on the track at one time so you cant go 100% as

you might have some slow person in front of you.

go do it tho for $25 + fuel (me $140 for the day) it's worth it

Yeah the 90 odd db rule would screw me over too.

So my speedo goes up to 180 and I havent had the stock ecu changed so its pretty much capped around there, so 80% of that is about 144. So basically couldnt go above 150 on the track at all.

That will make bugger all difference if I have a GTR thats got an aftermarket ecu up my ass, as their 80% will be alot more than mine. :)

Either way, I know that their thinking is mainly for safety, but they should focus more on safe overtaking. Considering the power difference there could potentially be with the cars, it could be safer if some of the slower cars were travelling faster than their 80% and the higher powered cars were travelling less than 80%. Ah well.

The 80% ruling is based on each individual drivers skill. Not speed, not how much power your car makes and its not the same standard for every driver.

They do this as a safety precution - it also happens at proper track days during passenger laps.

If a driver is seen to be 'overdriving', ie constantly off the track and in the dirt, or struggling to keep the car straight, etc etc, they may considering you are driving above your abilty, and as that can be a concern, expeically at these days where there are often passengers in cars, they may ask you to leave.

They say "80%" as a way of telling people that this is not a sprint event (hence the title "Fun Day") and that they wont tolerate people pushing themselves past their limits on the track at these days.

Having said all that - these days are a great way to have a go on a track if you havent done so before. Its sometimes a little scary due to number of cars on the track at once, but again, if you are only driving at 80% there is little that can go wrong.

Anyways.... the above is my interpretation and if anyone wants/needs further info, I suggest you contact Winton and have a chat to the event organiser about it.

Thanks for the feedback, its something ive been wanting to do for a while. I cant do it this time round but I am interested in the future.

More that I want to learn to control my car better. When it kicks out I can correct it in some occurances, but I want to get better at that and the public streets arent the place to practice. A track day would be ideal to practice control in some faster situations.

I understand what you mean now by the whole 80% being the drivers ability rather than the cars ability. Im sure many SAU members would drive my car 10 times better than I can. :nyaanyaa:

The noise restrictions are measured at 30 metres at a registered point and must be under 95db

The Fun Day is designed for those who have road cars that have never been on the track before to go out and see if they like it without spending big bucks and buying a licence. We have special permission to run the day without licences but that means that cars must only travel at 80% of their capabilities.

Anyone wanting to go fast and get timed, there are 4 Tampered Motorsport Track Days next year, and 5 Round of the Winton Sprint Series which you can go too and have your car timed electronically.

The Fun Day is the very very entry level into motorsport.

Cheers

Adam

hmmm sounds good, I was just worried about the 95db thing. But by the sounds of it it should be ok. My car cant be that loud as i drive it on the street everyday and have never had any problems but i reckon it would prob be over at an epa noise test

winton fun days are just show up, pay and get scruteneered and away ya go.

They getting pretty busy though so you really need to watch your mirrors and be carefull of dickheads that have no idea.

as for the noise, trust me. DONT WORRY. there have been a number of days i went to a around 18 months ago that ex v8 supercars (ea falcon) have been out testing along with hq race cars, open wheeler formula fords and a gt3 (once)! trust me, no skyline is as loud as them.

if you havent been to a track day i highly reccomend it, unbelieveable fun the first time you head out and think...... holy crap...... im on a race track!

if you are planning on having a bit of a dip make sure your brake pads are healthy. also reccomended that you give car a service afterwards if going hard.

fuel is available at the track but is expensive, 100 octane is on pump too!

hope the info is helpfull

enjoy

brett!

this wasy first track day, and i had soo much fun. was a great day

i would love to see pics of my car on the track or even a video as i saw a few video camera's around wen i went past the standing area. i was driving the white r32 gtr.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...