Jump to content
SAU Community

What Events Does Sau Vic Have In The Next Few Months For A Less Experienced Driver?

some_cs_student

By some_cs_student,
in Victoria

 Share

Recommended Posts

some_cs_student Veteran

some_cs_student

Posted
  • Author
Posted
two decent bolts should be sufficient. i have 4 in each extinguisher. i would not be a fan of just 1 bolt. and just to be sure, you are using nuts and bolts, not screws? lots of people screw them in and get knocked back.

4 bolts? Where? Why? :huh:

Anyway, I'm not a fan of 1 bolt but its a street car that *rarely* sees the track (due to $$$), I'm using the rear footwell so one bolt, no nut!

The rear seats have a bolt at the bottom on each side that secures the rear seats in, I've got the Fire Extinguisher with 1 bolt (well its now an allen-key like bolt) going through the extinguisher then securing the rear seat.

I am just using one bolt in mine, with an oversized washer.

The bolt that is used to hold in the rear seat, in the footwell.

Same here, only question is have you done AASA / CAMS events with it before? Just been paranoid, last thing I want is to get knocked back after driving to Shepparton.

dezz Grand Master

dezz

Posted
Posted

You won't get knocked back at DECA. I dare say 99% of people that have them mounted in the rear footwell are only using the 1 botl (Just as I do, and I've done plenty of DECA's)

Do-Luck Veteran

Do-Luck

Posted
Posted
You won't get knocked back at DECA. I dare say 99% of people that have them mounted in the rear footwell are only using the 1 botl (Just as I do, and I've done plenty of DECA's)

But now they will proably notice, and check :thumbsup:

Belsil80 Mentor

Belsil80

Posted
Posted
4 bolts? Where? Why? :thumbsup:

Anyway, I'm not a fan of 1 bolt but its a street car that *rarely* sees the track (due to $$$), I'm using the rear footwell so one bolt, no nut!

The rear seats have a bolt at the bottom on each side that secures the rear seats in, I've got the Fire Extinguisher with 1 bolt (well its now an allen-key like bolt) going through the extinguisher then securing the rear seat.

Same here, only question is have you done AASA / CAMS events with it before? Just been paranoid, last thing I want is to get knocked back after driving to Shepparton.

4 bolts in the 4 holes of the mount into the floor pan and tunnel. why? because 4 will spread the load better and there is no chance of getting knocked back at a track day. bolting it to the seat mounts would drive me nuts if the seat is on rails as i cant see it not being in the way.

anyway, seat bolts are rather large and would do the job fine, and as al said, an oversize washer is a good idea, however as you said it could be the reason you get knocked back at a cams day. it all depends on the scrutineer you get and weather you drive a datsun ;) you will be fine at deca.

Al Grand Master

Al

Posted
Posted

I have done an offical CAMS track day with the same one bolt mounting method and did not have any issues. I know Snowy used the same method for years, when his car was more street than track, and he never had any issues (as far as I know).

Scotsman Veteran

Scotsman

Posted
Posted
Same here, only question is have you done AASA / CAMS events with it before? Just been paranoid, last thing I want is to get knocked back after driving to Shepparton.

The one bolt setup your describing is the same way most of the motorsport guys do it, and have done at CAMS L2S events for 4+ years. This is how my car / snowys car runs at Dutton Rally with two extinguishers (one each side).

Basically if a scrutineer can grab the fire extinguisher and give it a shake and it doesn't move, you pass! So one bolt can do this and get you a pass, but what ryan is saying is correct, we all 'should' mount them better, and if a scrutineer does take a closer look then they would probably be within their right to knock you back. Bottom line is you will be fine for DECA and most of the time you will pass L2S sprint days. Just make sure that I can come along and see a metal bracket fire extinguisher mounted securely enough that I can't shake it loose (move the bracket). This is what I advise my scrutineers to check for.

Ryan - They are talking about the rear seat foot well (rear seat mounting point) not the front seat, so seat rails aren't an issue.

If we were all to rock up to a C3 race meet with this mounting system, I imagine we would all be going home early thou.

Snowman Grand Master

Snowman

Posted
Posted

Or you do what I "maybe" used to do and when presenting for Scrutineering take the extinguisher out of the holder and keep it in your passenger seat. That way you can hand them the extinguisher to check the date (the main thing they want to look at) and if they ask where it is bolted just point and then they can't "shake it around" and complain. They will just look at it and say OK.

Thats what I might have done for years and years without a problem :P

(This was for the 1 bolt rear seat footwell jobby)

some_cs_student Veteran

some_cs_student

Posted
  • Author
Posted
The one bolt setup your describing is the same way most of the motorsport guys do it, and have done at CAMS L2S events for 4+ years. This is how my car / snowys car runs at Dutton Rally with two extinguishers (one each side).

<cut>

Ryan - They are talking about the rear seat foot well (rear seat mounting point) not the front seat, so seat rails aren't an issue.

<cut>

If we were all to rock up to a C3 race meet with this mounting system, I imagine we would all be going home early thou.

Understood with C3 events, thanks for the information there, just wanted to confirm that I'm not doing something stupid by using only 1 bolt, and I don't exactly intend on real racing :)

Ryan, there is 1 bolt on each side securing the bottom section of the rear seats, ie. just behind the driver/passenger seat, under the rear seats, there is a bolt that secures that bottom cushion in, that's where I'm bolting too.

Due to the way the Fire Extinguisher is designed I've drilled the top / bottom hole out, the middle section is where the hinge is so it can't be drilled there, as long as the bolt is tight it should be secure :banana:

some_cs_student Veteran

some_cs_student

Posted
  • Author
Posted
Or you do what I "maybe" used to do and when presenting for Scrutineering take the extinguisher out of the holder and keep it in your passenger seat

Well what I may or may not do may be the same thing :)

Excellent idea.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 · Posted

      I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...