Jump to content
SAU Community

Eye-level Brake Light

Dingus

By Dingus,
in Western Australia

 Share

Recommended Posts

infamous_t Veteran

infamous_t

Posted
Posted
Where in WA can you get an eye-level brake light that is needed for compliance on cars that are imported but don't have one? Removed my spoiler, so need to get one on the car now.

HELLA makes good LED ones, have one on my GTR for compliance.

Few dealers around Perth.

Product: http://db.hella.com.au/cgi-bin/catalogue.p...amp;flmaint=335

Mr. Keets Grand Master

Mr. Keets

Posted
Posted

I had one of the Hella units..as above, Damn thing gave me a blind spot. Found one at some super ricer type store in Blacatta near the freeway on ramp. 20mm high x 100mm wide...*must remember to install the stupid thing*

Edit here pll..just checked the ADR's "60.2.4.1. have an effective projected luminous area not less than 29 square centimetres;"..looks like i'm measuring the damn thing when I get home

  • 2 weeks later...
NISZILA Grand Master

NISZILA

Posted
Posted

I just put a high level brake light in today. I bought a Navara LED Brake Light. P/No, 84650BL if anyone is interested. It has double sided tape to stick to the windscreen and enough wire to go all the way through to the boot where you can wire it into the plug originally going to the spoiler. Looks really good, very happy :)

Now I just need my new spoiler painted and then I can fit it :blink:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...