Jump to content
SAU Community

Aircon Help.

KrisG

By KrisG,
in General Maintenance

 Share

Recommended Posts

KrisG Enthusiast

KrisG

Posted
Posted

Ok after reading some threads on Aircon and reading the R32 not cold one. I did the test, Now i have an r33 so i dont know if the tests are the same but i held down the off button untill all the things lit up and went through the codes. They were "2,3,41,5" as i pressed the up down button. What does this mean. I just got the air con regassed the other day its cold but im paranoid. Any help would be good.

Link to comment
https://www.sau.com.au/forums/topic/198044-aircon-help/
Share on other sites
infamous_t Veteran

infamous_t

Posted
Posted

Does your aircon work? if so don't worry, otherwise...

Hold down 'cold' button i normal use till it goes to full cold... if it gets nice and cold its a sensor fault, anything else and its probably going to be an expensive fix.

Link to comment
https://www.sau.com.au/forums/topic/198044-aircon-help/#findComment-3537876
Share on other sites
adam-__- Grand Master

adam-__-

Posted
Posted

Yep, try put the system in the coldest setting and note how cold it gets. Then push and hold the cold button for roughly 10secs or until 'FC' comes up, then check how cold it is again. If it gets cooler, it could be the sensors playing up.

Link to comment
https://www.sau.com.au/forums/topic/198044-aircon-help/#findComment-3537886
Share on other sites
KrisG Enthusiast

KrisG

Posted
  • Author
Posted
Yep, try put the system in the coldest setting and note how cold it gets. Then push and hold the cold button for roughly 10secs or until 'FC' comes up, then check how cold it is again. If it gets cooler, it could be the sensors playing up.

Do i hold in the little blue arrow? I did that for 10-20 secs and i dont see a "FC" come up? By little blue arrow i mean the one that is next to the red one to make it warmer.

Link to comment
https://www.sau.com.au/forums/topic/198044-aircon-help/#findComment-3538300
Share on other sites
adam-__- Grand Master

adam-__-

Posted
Posted
Do i hold in the little blue arrow? I did that for 10-20 secs and i dont see a "FC" come up? By little blue arrow i mean the one that is next to the red one to make it warmer.

Yep, that's the one to hold. Make sure you hold it down for the complete 10sec or whenever the 'FC' comes up. It takes a while.

Link to comment
https://www.sau.com.au/forums/topic/198044-aircon-help/#findComment-3538471
Share on other sites
adam-__- Grand Master

adam-__-

Posted
Posted (edited)
Im not seeing this FC come up do i need to be holding the button when start the car? Ive held it for over 30 seconds, Does it come up on r33?

Yeah, the car should be on for the air con to work. Not completely sure if they come up on the R33's though. 30 seconds is a long time to be holding it though, good work. :)

Edited by adam-__-
Link to comment
https://www.sau.com.au/forums/topic/198044-aircon-help/#findComment-3539775
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...