Jump to content
SAU Community

Recommended Posts

hey,

Just a quickie, how do you tell the differance between a R33 GTR and a R33 GTR VSPEC?

Is it in the vin number or is there another easy way to tell?

As im looking around at a few GTR 33s now and most claim to be a VSPEC model just wondering how do i know for sure it is?

also do some come with airbag steering wheels and others come with a non air bag with GTR on it?

Edited by Adz2332
Link to comment
https://www.sau.com.au/forums/topic/198249-gtr-or-gtr-vspec/
Share on other sites

This is what I know - and stand to be corrected... VSPEC GTR's have better seat trims, bigger boot and a bigger turbo plus the front GTR lip looks more curvier like a nismo lip.

None of it is correct.

All R33 GTRs have airbags standard , Series on e have drivers side standard and passengers side option, all series II and series III have standard drivers and passengers side .

The vin will tell you for sure is it is a V-spec or not . The main difference , V-specs have a finned rear diff and ALSD on the cluster, attessa is different but hard for you to tell. they have slightly harder dampers and they are a little lower .

None of it is correct.

All R33 GTRs have airbags standard , Series on e have drivers side standard and passengers side option, all series II and series III have standard drivers and passengers side .

The vin will tell you for sure is it is a V-spec or not . The main difference , V-specs have a finned rear diff and ALSD on the cluster, attessa is different but hard for you to tell. they have slightly harder dampers and they are a little lower .

Bingo!!!

This thread can assist.

http://www.skylinesaustralia.com/forums/Me...ml#entry3529122

1. The very best way to determine if your car is a v-Spec is to check on the Vin number on the following thread

http://www.skylinesaustralia.com/forums/Ni...&start=1060

2. Tell tail signs are:

Vspec has active LSD (a yellow light in the dash)

Vpsec has the faster attesa computer 1/1000th of a second rather than 1/100th (not visually noticable)

Vspec has stiffer suspension stock 10mm lower (not visably noticable)

10kg more weight (not visably noticable)

A Vspec sticker

Air difusers for the front brakes

Slightly better ABS (not visually noticable)

Finned rear diff

This is what I know - and stand to be corrected... VSPEC GTR's have better seat trims, bigger boot and a bigger turbo plus the front GTR lip looks more curvier like a nismo lip.

lol dood wtf?

bigger boot? race drivers need that extra room for the golf clubs must be :banana:

series 3 vspec had nicer trimming ie red stiching. that was 97+ though

bigger turbo? hardly

lol dood wtf?

bigger boot? race drivers need that extra room for the golf clubs must be :banana:

series 3 vspec had nicer trimming ie red stiching. that was 97+ though

bigger turbo? hardly

All series III have red inserts, makes no difference if they are V-spec or not .

None of it is correct.

All R33 GTRs have airbags standard , Series on e have drivers side standard and passengers side option, all series II and series III have standard drivers and passengers side .

The vin will tell you for sure is it is a V-spec or not . The main difference , V-specs have a finned rear diff and ALSD on the cluster, attessa is different but hard for you to tell. they have slightly harder dampers and they are a little lower .

Wow, that's all? The price difference from what I know is quite substantial.

And you missed one thing; the VSPEC GTRS have the VSPEC badge. lol :banana:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
    • Literally looks like direct port nitrous haha
    • They are in fact just nozzles. They are there only to produce a spray pattern and limit flow. The injector itself is what I use to control flow to the 7x nozzles. My old system had no injector and only PWM the pump. This lead to a lot of inconsistencies, and poor atomization at low pressure when the pump was ramping up. 
×
×
  • Create New...