Jump to content
SAU Community

Recommended Posts

If they bolt right on, you'll probably need the 4 door bootlid as well. The edge tapers at an angle to match the light, where the 2 door one has a curved corner.

can anyone comfirm this?? if they bolt straight on and only need 4 door bootlid, i wouldn't mind to do this also .. like 4 door rear lights tho

cheers

You're going to need the rear bar as well.

From what I can see, I don't think they'll be a straight swap over. The part where the indicator is on the sedan's, the lights are more curved compared to the coupes.

My answer would be that it's not a straight swap over, but then it doesn't hurt to try it for yourself.

its a straight fit with some minor modifications (well it is when changing from 4dr lights to 2dr lights)

from 4dr to 2dr you will need:

2dr bootlid

rear bar

both taillights

to make the taillights fit, you gotta cut away abit of the metal where it slots in to make it sit neatly, at the bottom of the boot, you will need to weld a 5mm metal strip on to make the gap as small as possible like as if it was an original 2dr rear. you can get away without welding the metal strip on but the gap from the rear boot > rear bar (above where it says skyline) will be like 2cm or a bit more.

i assume it would be the same when going from 2dr lights to 4dr except for the welding of the metal strip and cutting away some metal to fit the taillights.

if anyone wants to do it, im willing to be up for a swap (ive got a 4dr) preferbly a silver skyline :D

i like the 2dr lights better, much more agressive and sexy looking

Edited by whyte

[QUO]its a straight fit with some minor modifications (well it is when changing from 4dr lights to 2dr lights)

from 4dr to 2dr you will need:

2dr bootlid

rear bar

both taillights

to make the taillights fit, you gotta cut away abit of the metal where it slots in to make it sit neatly, at the bottom of the boot, you will need to weld a 5mm metal strip on to make the gap as small as possible like as if it was an original 2dr rear. you can get away without welding the metal strip on but the gap from the rear boot > rear bar (above where it says skyline) will be like 2cm or a bit more.

i assume it would be the same when going from 2dr lights to 4dr except for the welding of the metal strip and cutting away some metal to fit the taillights.

if anyone wants to do it, im willing to be up for a swap (ive got a 4dr) preferbly a silver skyline

i like the 2dr lights better, much more agressive and sexy looking[QUO/]

have you found a thread, going through this in more depth or have you done it yourself? because i agree with you on the 2 door lights looking tougher and much sexier :thumbsup: and i have been looking for a decent thread or some kind of write-up about how to convert to the 2 door lights on a 4 door. like this :D

IMG_6729i.jpg

Only decent pic i could find, was from driftfest.

Edited by Greasy

Not trying to sound rude to you all, but all of you guys are wrong.

I personally have converted a sedan to coupe tail lights (see pic)

65978195gd2.png

39925490ob9.png

83744154wi5.png

39744490gk6.png

23077190go2.png

None of the parts are interchangable. The coupe boot lids are wider. And the coupe tail lights have a bigger (note: much bigger) bulb holders.

Bumpers do not fit as well, you gotta redrill everything

Edited by Chang

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...