Jump to content
SAU Community

Recommended Posts

for the tech boys :D

i will be using my hks actuator to control my boost setting at what ever the spring rate is set to which i think is 12-13 psi.

just want to know what size boost jets should i run to achieve 15 psi.

for the r33 gtst

thanks guys.

Edited by R33GOD

The jets fit in the end of the wastegate vacuum hoses. These attach to the fittings on the intake pipe before the rubber intake hose that feeds each throttle body.

boost jets....

if you guys go to the 300zx forum they clearly tell you what they are and how to install them.

my dad done it on his 300zx. stock setup. runs 12 psi nicely with no boost spike

The jets fit in the end of the wastegate vacuum hoses. These attach to the fittings on the intake pipe before the rubber intake hose that feeds each throttle body.

boost jets....

if you guys go to the 300zx forum they clearly tell you what they are and how to install them.

my dad done it on his 300zx. stock setup. runs 12 psi nicely with no boost spike

Boost controller or boost jets:

Boost controllers and boost jets are the recommended way to increasing your boost pressure. Adding a boost controller essentially tricks your waste gates, waste gates vent boost allowing the car to just run at 8 psi. The boost controller or boost jets trick the waste gates into thinking that there is less boost than there really is meaning you will have a quicker spool up time and a large increase in total boost pressure. Boost pressure equals power. Running higher boost pressure is only capable after an ECU upgrade. Investing in a turbo timer is also a good idea when running higher than stock boost, as a turbo timer will help cool your turbos when its time to shut down.

i'm still confused

WOW, upping the boost to 12psi will help my turbo spool quicker........ :D

And i need an ecu upgrade to run higher boost.... :devil:

The only thing i can think a boost jet is would maybe be a tube of something with a smaller hole in the centre so it lets less air through to the wastegate.

Just get a boost controller and do it properly from the start.

yes i mean an actuator, most of the ones i have seen are adjustable so it should do a fair bit of boost, with one of these i dont understand why you need the extra bits.

You hav'nt really explained your self very well, got any pics of what you are chasing?

reason why i dont want to depend just on the actuator is because iv'e heard from a few people so far that when you run them on what there set from factory (12-13psi) they work better than a boost controller but when you try to increase the boost pressure through the rod boost will come on abit slower and will tend to spike.

no pics at this stage mate

Just so I understand, boost jet is a fancy name for a non-adjustable bleeder type boost controller, right?

Never heard it called that before. Anyhow, bleeder valves are generally the worst type of boost controller.

If you want to do it on the cheap, you'd be better off installing a precision spherical coil actuated pressure regulater install, which is more commonly referred to as a ball and spring boost controller. :D There's a great one on ebay for about $35, search for 'Turbotech'.

people that mock this way of boosting a car dont know about this method. need some tech guys who know what there talking about and that have played around with these jets.

rofl :D

I wouldn't think you'll find a "tech guy" as you mention it, using one of these "boost jets" on a skyline for obvious reasons. A $20 bleeder would prolly be a better option

Note my use of quotation marks for "boost jet", much like "Santa Clause" "Easter bunny" and of course "hot lesbian"

I wish you luck

Edited by GeeTR

forget the term boost jet and call it what it actually is. A "Restrictor"

its a small piece of steel tube that is fittted snuggly inside the actuator supply line from the manifold.

it has a smaller hole in the middle approx 2.5 - 3mm compared to the 6mm rubber line.

im running one in conjunction with my PFCBC and a 18psi actuator and i have no issues controlling boost up to 27psi.

ramps onto boost hard, and then stays within 1psi to redline.

and just to clarify an earlier remark in regards to increasing boost can make it come on sooner.

if your target level is close or just past your actuator tension, then your internal gate flap will allready be opening before you reach your target boost as to control the clime in pressure. If you were to run a heavier actuator and run higher boost then the flap will stay completely shut for longer causing it to ramp up harder and earlier.

not 1000rpm sooner but certainly 100 - 300rpm sooner.

FYI.... Sydneykid had posted this earlier on a different thread [http://www.skylinesaustralia.com/forums/Jaycar-Boost-Fuel-Contro-t61207.html&st=20], may be of assistance?

" 30 Jan 2005, 10:59 AM Post #37

I thought everyone with an RB25DET knew how to do it. You just disconnect the solenoid (vacuum, not electricaly), connect the boost feed directly to the wastegate and use the (standard) restrictor to bypass the desired amount back into the turbo inlet. The standard byspass hole of 1.25 mm bypasses enough air flow for 0.5 bar. Tools needed = one pair of pliers and 10 minutes.

PS; If you want more boost you can drill out the bypass, 1.5 mm = more boost (around 0.7 bar) 1.75mm = a bit more (around 1.0 bar). But the Jaycar Boost Controller needs the bypass to relieve trapped pressure between the solenoid and the wastegate actuator. So I don't want to redrill the restrictor only have to solder it back up again."

"This is the 10 minute no cost boost to 0.5 bar rerouting of the vacuum hoses. Disconnect the two vaccum hoses from the solenoid. Then connect the boost feed (from the cross over pipe on the left of the picture) to a the standard T piece. Connect one side of the T piece directly to the wastegate actuator (on the right of the picture). The remaing connection on the T piece goes back into the inlet via the BOV return pipe (on the standard fitting). Make sure to put the the standard brass restrictor in that vacuum hose to bypass the desired amount back into the turbo inlet. The standard bypass hole of 1.25 mm bypasses enough air flow for 0.5 bar."

If I could work out how to insert the photo I would have soz lol... noob here... hope it helps whoever :-)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...