Jump to content
SAU Community

Recommended Posts

Some small facts first off - r33 gtst s2 (1996) with no mods apart from apexi pod.

I recorded a video using my mobile phone so the quality isnt the greatest. Ill try to provide an explaination to help.

http://www.youtube.com/watch?v=02Cyv2CWqDU

In the video you can see that my idle is fluctuating from about 100-1000rpm. This occurs when ive been driving the car for around 5-10 minutes, or generally once its all warmed up properly. You may also notice that as the rpm fluctuates, so does the vac/boost.

About 3/4 through the video you can see me open the throttle a little bit. The following is what i deal with on the roads when driving. Say im in second and approaching a corner or roundabout and have to give way so i slow down. Its very likely that the car will completely drop off all rpm and die on me. In the video im in neutral or first with the clutch in i forget. Either way, when im in first and i start to slow down a bit after opening the thottle, its very likely that the rpm will drop off to around 0 but not actually stall completely. As seen in the video i rev it a bit, then the rpm drops to about 0 and the battery light flashes for a second but the car doesnt actually die.

Anyway, i plan to take the car to a workshop/garage this month to solve this issue however if i can do this at home id be excstatic.

After searching the forums heavily ive come to the conclusion that it may be caused by one of, or a combination of the following:

-faulty afm

-leaking i/c piping

-dirty aac valve

-faulty o2 sensor

-faulty tps

Ive read that cleaning the aac valve can do wonders; is this the type of problem i can solve by cleaning the aac valve at home? It's just that i dont have a large amount of cash to wave around so being able to fix this my self would be great.

Link to comment
https://www.sau.com.au/forums/topic/199778-is-this-idle-hunting-bad-idle/
Share on other sites

if not a factory computer, this can be caused by having the first few cells of the map unbalanced, ie on powerfc first 3x3 should be the sameish in fuel and timing, otherwise you get this sort of thing as it jumps through bouncing off different values.

if standard ecu, check your afm wiring and plug, and if all good try cleaning or getting a replacement aac valve

mine did this when rolling up to a set of traffic lights in neutral

it was the AAC valve. You can check this by temporarily disconnecting it. if ya idle doesnt fluctuate after disconnecting it, well theres ya problem

i ended up putting on a sr20 aac valve that was apperantly the same and doesnt do it anymore.

I had the exact same symptoms as you after pulling everything apart for a turbo upgrade (pulsing idle when stationary with car warmed up). In my case it turned out to be an air leak. Check all vacuum hoses connected to the crossover pipe and intake manifold for broken/split ends. Also check your Intercooler piping and make sure there are no leaks after the AFM. Definitely clean your AAC Valve regardless as many have mentioned.

Gave the AFM a good clean today, the inside was full of black shit. Gave it a clean with some electrical contact cleaner and put it back, the car seemed to run better than before. It still has a rough idle at times but its not as frequent.

Tomorrow i'll be cleaning the aac valve, hopefuly that helps.

  • 2 weeks later...
In the video you can see that my idle is fluctuating from about 100-1000rpm. This occurs when ive been driving the car for around 5-10 minutes, or generally once its all warmed up properly. You may also notice that as the rpm fluctuates, so does the vac/boost.

I have the same thing. At first I thought it was a Vacuum leak, but after testing with soapy water and listening with a hose I found nothing. Now I suspect it is a faulty O2 Sensor. When the car starts idle hunting try disconnecting your O2 Sensor and wait around 30seconds. When I did this my idle stopped still at 900rpm.

My theory is that the car runs fine until the O2 Sensor is warmed to operating temperature as the ECU ignores this reading until that time. Once the O2 sensor is operating, the ECU reads a false value and idle struggles as the O2 Sensor is not able to keep the ECU up to date with accurate readings. I tested my O2 Sensor at operating temp with a multimeter and noticed that it does not vary in voltage as it should. I am going to test another O2 Sensor. Will let you know how it goes.

Very interesting theory. Last week i gave my aac valve a very good clean. At first it seemed like the problem disappeared but after about 30min of driving it happened but only to a small extent. No where near as bad as it was before. The aac valve cleaning definately helped.

Unfortunately, i havent been able to drive my car enough to see if the problem has gotten any better. I got busted driving it last week and got 2 fines, one for it being manual and the other for high powered vehicle (im a p-plater). Its my second car and i drive it like once a week but i dont feel like risking more fines. Im fully licensed next month though.

The o2 sensor stuff sounds like its worth a try if it happens to me again, ill keep it in mind.

thats how my car was running when i took the BOV off and turned it on LOL

so definately check for leaks in all piping such as vacuum and intercooler/intake side of things

but as others have mentioned before try someone afm

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all,  I am in the market for an R200 longnose diff out of a Z31 300ZX, or S12 RSX, DR30 skyline, or similar, in a 3.9 ratio.  Preferably a late model one with the M12 crownwheel bolts.  The only easy to find advert for one of these was my ad back in 2007 when I sold it on this forum.  I sold the diff as I had sold the car it goes to, but as it turns out, after 18 years I got the car back late last year, so now I'm looking for the diff !  If anyone knows where to find a longnose R200 LSD with the M12 crownwheel bolts, drop me a line at [email protected] - Bonus paid if soomeone comes up with the original diff (stranger things have happened !).  Cheers   Ben D    
    • Hi everyone, I used to post here a bit from 2004-2013, when I owned various Nissans, in particular my S12 RSX gazelle, which was sold in 2007.  As luck would have it, after an 18 year hiatus, the car found its way back to me last year, and over the past 11 months I have had the pleasure of restoring it with my kids.  One thing that I am after in particular is a 3.9 ratio R200 LSD for it.  I actually sold the one out of the car here back in 2007 , and it would be incredible if I could track down who I sold it to, so I can see how they have progressed over the years (and to be honest, to see whether I can get the diff back !).  Anyways, hi all and let me know "where are the R200 Longnose diffs all at these days ?  Cheers Ben D  
    • Arms will be the same as the G35 or 350Z, but as above, there was a change in the lower control arm where it connects to the ball joint.  That said, you can remove the ball joint cone from your old ball joints and fit them to the new ball joints.  To be honest, I didn't think the ball joints themselves were different. The main ball joint is a bit awkward to replace, you really need to remove the steering knuckle to press out the old one.  Some people have used tools to remove it in place, but it just seemed too hard to get to. If you are going to press out/in that ball joint, then you may as well just replace the bushings in the LCA and the compression rod.  You can buy the compression rod bushing from Nissan, but the LCA bushes, you will need to go aftermarket. Much cheaper than buying the whole arm.
    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
×
×
  • Create New...