Jump to content
SAU Community

Recommended Posts

Nissan Skyline 93 R33 FRESH comp motor 4263 KLMS old - RB 26 head on RB 30 block completly new motor Powed by Haltec E11 v2 ECU, Rb 30 block machined ported polished all ACL bearings / new pullys , compression 8.5:1,Anti Oil surge fins in sump for track use Balanced crank shaft new ACL bearings mains, Argo I beam conrods balanced connected with High tensile ARP rod bolts, Weisco forged piston and ring kit balanced, GTR N 1 oil pump, RB 26 GTR head ported and polished with ferra comp valves and springs over size on the outlet cam shaft to flow more air, ARP 12 mm head bolt/stud kit, Tomei cam shafts 270 duration / 10.4 lift, Greedy cam gears, GT42 r ball bearing turbo rated 1000 hp fitted with braided line and anodised speed flow fittings, Custom polished top mount stainless steel manifold external wastegate, Wastegate XTR 55 mm 2 inch screamer pipe, Greedy fuel rail, Sard 1000 cc injectors & regulator, All speed flow fittings for the turbo and fuel set up, Magna fuel filter, Over size comp fuel lines linked to surge tank , Bosch 044 - 700 hp pump / Walbro 500 hp in tank pump, Os giken twin plate clutch, 19 row oil cooler with remote filter and braided lines, Large intercooler with polished mandrell pipe work, K&N Air filter, Oil catch can, Turbo smart super sonic B.O.V, Exhaust polished mandrell bent 4 inch dump pipe of turbo into 3.5, through to cannon tip, HKS super drager coil over suspention, Front and rear strut bar, Light weight deep dish 18 x 9.5 fitted with 245/45/18 continental sport contact 2 rrp 650 ea, rear hankook 285/35/18 Full body kit, Fresh New Mazda 6 Blue, ----power 424 rwhp on 14 psi built to handel 800 HP on final tune. Regretful sale due to morgage and kids ,no swaps and please no time wasters. CALL 0433 233 177 after 6 pm. [email protected].

post-46177-1199584363_thumb.jpg

post-46177-1199584672_thumb.jpg

post-46177-1199584797_thumb.jpg

post-46177-1199584939_thumb.jpg

post-46177-1199585215_thumb.jpg

post-46177-1199585391_thumb.jpg

post-46177-1199585490_thumb.jpg

Edited by rb26rb30r33sellinglook
Link to comment
https://www.sau.com.au/forums/topic/200364-for-sale-r33-rb-26-0n-rb-30-block/
Share on other sites

price !! interested if this can be sent and complied in WA, and price is right of course. by the way how can u handle that much power at back wheels only ??

I'm pretty sure 285's on the rear will do it lol.. I got 245's on my 400hp gtr and it goes alright in rear wheel drive launches.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...