Jump to content
SAU Community

Recommended Posts

depends where the cop who is doing the defect sends you!

oh its not for a defect..i bought my car from VIC and need to get it registered here in SA so it has to get checked and all but my hicas has a little leak so im gonna put a hicas lock bar there instead.

Hi, I've changed two cars over from different states and you don't need a check at all. As long as the car is being registered in the same name as in the previous state you just go into the office and show them id and your previous rego slip. Hand over the old plates and they'll give you new ones.

Cheers,

Matt

oh its not for a defect..i bought my car from VIC and need to get it registered here in SA so it has to get checked and all but my hicas has a little leak so im gonna put a hicas lock bar there instead.

He is putting the car in his name though so at the very least you will have to go to sturt, just depends who you get on the day as to wether it will pass or not. If you havnt already purchased one we have them in stock for $99.

Ryan

Hi, I've changed two cars over from different states and you don't need a check at all. As long as the car is being registered in the same name as in the previous state you just go into the office and show them id and your previous rego slip. Hand over the old plates and they'll give you new ones.

Cheers,

Matt

so hopefully u changed the name on the interstate rego to ur name, then there will be no hassles :D

my car ended in inspection cos it was registered in the interstate owners name, and the person that i got it from never put it in their name (previous SA owner)... i made sure that they cleared it all with regency b4 i bought it and only had to empty my wallet for the rego/stamp duty/interstate transfer fee/new plates.

He is putting the car in his name though so at the very least you will have to go to sturt, just depends who you get on the day as to wether it will pass or not. If you havnt already purchased one we have them in stock for $99.

Ryan

You sell hicas lockbars? Want one for my car, stupid hicas light flashs on when i turn a bend at speed then goes off once i straighten up, gets annoying.

Sorry bit off topic but one quick question, does the hicas have anything to do with the power steering? Hicas light comes on and i lose power steering, Fill up the power steering well and the light goes off and i get power steering back..?

You sell hicas lockbars? Want one for my car, stupid hicas light flashs on when i turn a bend at speed then goes off once i straighten up, gets annoying.

Sorry bit off topic but one quick question, does the hicas have anything to do with the power steering? Hicas light comes on and i lose power steering, Fill up the power steering well and the light goes off and i get power steering back..?

Hicas provides active feedback to the steering wheel... think Force Feedback on an arcade game...you know there are no kinetic forces but the actuators are giving you more of a feel... faster u go, the stiffer the steering gets, which is ideal... one of the worst things about power steering is the overresponsiveness (is that a word?) at high speed... hicas mitigates this to a degree thru the steering wheel (or Boss kit if u get an aftermarket system).... theres another forum thread which goes thru the ins and outs of hicas... basically it helps when you're an inexperienced race driver or an everyday driver... if you do any serious track work, chances are your skills will be higher than required for hicas, however that said, hicas can cause a very steep, very quick corner exit if you have the skills for it, as even a small amount of rear wheel toe in has a significant effect on cornering (Apparently, Dont look at me for details, im a noob)...

No doubt it un-nerves anyone whos not used to it, but once u get used to it you'll wonder how you lived without it... as mentioned before, nissan have kept hicas since the r31, so I really doubt theres any convincing reason to get a lock bar, aside from finances, or superultramegahardcore racing

I have hicas problems at the moment myself. im hoping when i get time to calibrate the system It'll come good, otherwise I'd rather spend the money to get the hicas fixed good and proper. Lock bars are for the hardcore, and i'm not hardcore.

-D

Edited by Dohmar

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
×
×
  • Create New...