Jump to content
SAU Community

R33 S2 Highflowed Turbo

rinmak
 Share

Recommended Posts

rinmak Proficient

rinmak

Posted
Posted (edited)

Hey guys,

I have a highflowed turbo for sale that came off a stagea I bought recently. The turbo would suit a rebuild as there is some noticeable movement back and forth on the shaft and also side to side. The compressor housing also shows the slighest signs of being touched by the compressor wheel on occasion. The turbo did not make any noise before it came off and had a slight amount of oil left in the cooler pipes.

I have no receipts for the work as it was done by previous owners but I will get pics of the front/rear wheels and its quite obvious that it has been highflowed as they are massive.

Still yet to get a quote from a turbo shop to rebuild this but I would expect around the $400-$500 mark.

Done a search here and these highflows seem to go for about 1300 bucks secondhand so im going to ask $600 for my one as is. Will eventually get a quote on rebuild and may even have this done then sell as a new turbo but I thought I would post it up and see if anyone else wants to take it as is.

Located in Perth but should be ok to post.

Regards,

Ryan

post-18921-1200432660_thumb.jpg

post-18921-1200432714_thumb.jpg

post-18921-1200432729_thumb.jpg

Edited by rinmak
Link to comment
https://www.sau.com.au/forums/topic/201581-r33-s2-highflowed-turbo/
Share on other sites
stolen_s15 Mentor

stolen_s15

Posted
Posted

I'm interested, but your dreaming if you think people will pay $600 for a turbo that needs a rebuild.

Also is it ballbearing or journal? Who did the original work? Any dyno sheets?

rinmak Proficient

rinmak

Posted
  • Author
Posted (edited)

Fair enough. I wasnt very sure on the price so im open to offers. Feel free to PM me with one. Il also get a quote on the rebuild and at the same time hopefully get some specs. Way I saw it was that people pay 1500 bucks to get their turbo's highflowed, and if my assumptions are correct then this turbo will only need about 400-500 worth of work done to get it rebuilt and working properly as a highflow...so its basically a new highflow for 1k give or take.

Anyway, il get some pics and a quote in the next few days hopefully.

Oh and sorry no specs or dyno sheets. Ive had the car 2 weeks and only drove it half a k before a cooler pipe fell of and subsequently got run over =/.

Cheers guys.

Edited by rinmak
rinmak Proficient

rinmak

Posted
  • Author
Posted

Ok guys I spoke to the turbo place today and they told me the following:

- Definitely a high flow (duh)

- Capable of about 450hp

- Scoring on the compressor housing is easily tidied up.

- Compressor wheel will need replacement as one of the fins is slightly bent ($120 for new wheel)

- To expect about $800 all up for a rebuild inc parts and labour....and it was a worst case scenario sort of quote.

So in light of this the new price for the turbo is 300 ono

rinmak Proficient

rinmak

Posted
  • Author
Posted (edited)

Pm me your post code mate

Il see if my local PO is willing to ship it and how much etc and make a decision from there!

Edit: Post code = zip code

Edited by rinmak
  • 2 weeks later...
  • 1 month later...
Fero Collaborator

Fero

Posted
Posted

turbo is off a series 1 or 2 skyline or equivelent , actuator though is defenently off a series 1 skyline which leads me to believe its a series 1 turbo. rear wheel is defenently bigger and front i think is noticably different like mine with room to go bigger still. rear whwwl is same size as mine. does it have a rear steel for sure???? also core of turbo has noticable blemish marks in the metal which is a sign or uneven heat on the core. as you already know turbos get very hot so try get some close up shots to inspect for cracksin the casting. Really though for 100 dollars i would just buy it any way and take my chances b4 somebody else snaps it up.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
×
×
  • Create New...