Jump to content
SAU Community

Recommended Posts

Hi Guys,

I've got an R34, and would like to have the centre console (cheap shitty black material) re coated.

Can anyone recommend anywhere to have this done? I live on the northern beaches and would prefer somewhere local if possible.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/201597-console-recoating/
Share on other sites

I'm going to get mine painted properly by Louie at Xclusive Colours. I've seen another car he has done like this (Malcolm's mega clean R33, was in HPI recently) and it looks good. I think he uses a satin kind of finish so it doesn't look home painted like people do.

Its easy to get car body paint look..

Drop it in some metho, bath it with a scouring sponge or somthing similar until all the old paint is removed, all is important!!

Then sand back with 1500 grit paper to remove most scatches you made.

Hit it with a Light coat of colour youd like, just buy body spray paint.

Then sand back with 2000grit

Then hit with heavier coat, then sand back again with water and 2000

Hit with heavyish coat but not full heavy, again sand back until smooth.

You may wish to apply a last coat now.

Clear mild coat and sand back heavy with 2000grit should be very smooth now

Then reapeat clear with two heavy coats and sanding in between, the last coat you do not sand.

Hit with a heavy cut and polish and you will have show quailty stuff.

They will basically do the same, may look better because you arnt a pro :D

I'm going to get mine painted properly by Louie at Xclusive Colours. I've seen another car he has done like this (Malcolm's mega clean R33, was in HPI recently) and it looks good. I think he uses a satin kind of finish so it doesn't look home painted like people do.

Louie did my R33 console about a year ago, still looks great and he was really cheap

Cheers

Johno

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys my TPS voltage is reading over 2v at idle.  My Haltech ECU is reading around 40% throttle position at idle also which is really strange. Note the actual throttle position sensor is brand new…    anyone have any experience with this or know how to calibrate it on Haltech ? 
    • The OEM disk will not work on any AEM ECU, you need to use the one they made. You shouldn't have to flip the CAS or whatever you were describing, if you set the ignition sync offset correctly it can't backfire. Make sure you're using a spark plug lead on coil 1 instead of the timing loop to avoid weird issues with the timing light. Double check that your timing settings are actually correct, like is the 24 tooth configured correct or should it actually be 12 teeth for 1 crank revolution? I also found this: 305817248-AEM-Undocumented-Settings-v1-2.pdf    
    • Yeah, I don't believe the M35 uses a deadhead system.
    • Have you done your thinking backwards? 3 bar, 43.5 psi pressure drop being the presumed specification for an injector, means you need 3 bar upstream when they are firing into atmospheric pressure, and more upstream pressure than that when on boost (you add your boost to your rail pressure to maintain 3 bar across the injector) and you need..... less pressure upstream when you have vacuum in the manifold. So, presuming that you're idling at -10 psi, then you only need ~23 psi in the rail. I realise that I did not need to say all of that to you specifically Matt, once you'd realised your mistake. It's mostly there for complete clarity for others.
    • Have you reached out to the guys at Spool Imports? They are a Ross dealer, I can imagine they would have the rings just sitting on the shelf (I could be wrong).  
×
×
  • Create New...