Jump to content
SAU Community

Recommended Posts

The cooling area of my R32 GTS-T has gone to bits.

1) When i run my car no water leaks it goes normal...when i park it and switch it off and say after 15 mins of cooling down, water begins to trickle from te centre of teh bay, so its more than obvious its the pump right?

2) The collant tank is the first to drain out, then say after a day or 2 the radiator begins to drain.

What the hell is going on man? And the water that i refill turns to smudge like brown and orange, i think there might be a blockage thus causing the discolour?

Help us out here fellas it would be much apreciated.

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/202393-whats-the-right-coolant/
Share on other sites

You could do a radiator/coolent flush, then do a pressure test on the radiator to make sure its not leaking, then check the hosing/pipes, make sure they are secured down with hose clamps.

I have not seen brown/orange colour coolent b4, Red (usualy for Toyotas) and the rest is Green. I use Techteloy 100.

Edited by (00)SKYLINE(00)
1) When i run my car no water leaks it goes normal...when i park it and switch it off and say after 15 mins of cooling down, water begins to trickle from te centre of teh bay, so its more than obvious its the pump right?

you mean it like leaves a puddle under the car like its coming from the centre of the bay? could be a pin prick hole in one of your hoses, i had a similar thing. would only leak once the car was warmed up, building enough pressure to make the coolent seep outta the tiny hole. was one of the heater hoses located under the plenum.

yours could be the same, maybe only the hole is smaller then mine was and needing more pressure to make it leak? turn the car off, the coolent sits in the still hot engine block with no circulation, boils that little bit more making the extra bit of pressure, leaks, then cools down sucking coolent back in from your overflow bottle/coolent tank and youre none the wiser..

just a thought anyway.. :S

i could run my car without the radiator cap screwed on tightly, allowing no pressure to build up and it wouldnt leak the coolent out the small hole. not recommened for driving but only just a test on the spot. maybe you could do something similar?

shaun.

The cooling area of my R32 GTS-T has gone to bits.

1) When i run my car no water leaks it goes normal...when i park it and switch it off and say after 15 mins of cooling down, water begins to trickle from te centre of teh bay, so its more than obvious its the pump right?

2) The collant tank is the first to drain out, then say after a day or 2 the radiator begins to drain.

What the hell is going on man? And the water that i refill turns to smudge like brown and orange, i think there might be a blockage thus causing the discolour?

Help us out here fellas it would be much apreciated.

Thanks.

if you dont maintain the coolant it eventually turns light green then can get fowled and get sludge in it and brown a bit.its important to flush that radiator if its dirty and replace new coolant mix.leak might be just a hose etc or a join.so gotta get there an see where water is going from,new pump will mean replacing it.better sort it sooner than later.

I had the same deal on my 31...

It seems like its coming from water pump???? i put some seal up in it just till engine is done. It worked well.

But i only did that cuz i'm building a engine and dont want 2 waste time on a sh!tty rb20, it would be the water pump gasket, or actual pump itself.

So if your keeping the engine, inspect and replace, when your there have a look at the shape its in "corroded or scummy" run a good system flush and have the radiator done aswell, cuz there is no point flushing your system and leave the rad alone.

mY 2C

if you dont maintain the coolant it eventually turns light green then can get fowled and get sludge in it and brown a bit.its important to flush that radiator if its dirty and replace new coolant mix.leak might be just a hose etc or a join.so gotta get there an see where water is going from,new pump will mean replacing it.better sort it sooner than later.

Wow, you've got a chicken in your cooling system?

The easiest way to check for a hose failure is to get the car warm & with a pair of gloves on squeeze each of the hoses in turn to see if they do in fact leak under pressure.

Or, if you are Welsh, leek under pressure.

Thanks for the info guys, very helpful. I think it needs a good flush because the water looks like its mud. I have noticed the ehating going up now aswell.

Another 2 questions.

1. My brother in law told me not to put just any coolant in there ,that i should read the manufactures manual and see what its compatible with. He told me that the brown sludge is not the coolant but the corosion the coolant is causing, and that anit freeze adnti boil stuff you can buy from K-Mart is hazardous to the car. Anyone back this up? And if so, what coolant do you reccomend. He told me to put Toyotas Coolant Inhibitator that you can buy from Repco.

2. Anyone can direct me to a website that shows step by step how to flush my system? Pictures would be helpful.

Thanks guys.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...