Jump to content
SAU Community

R34 Gtr Parts And Performance Parts

lahsak80
 Share

Recommended Posts

lahsak80 Apprentice

lahsak80

Posted
Posted

R34 GTR and Performance Parts

- RB26 R32 GTR Complete Engine $6000

Roughly done 60***Kms, perfect working and running order. Comes with everything including twin turbos, intake pipes, injectors, plenum, throttle bodies, pullies, sump. Does not come with computer or wiring harness.

- R33 GTR Brembo Brakes $2200

Complete set which include Front Brembo Calipers, Rear Brembo Calipers and Bendix Pads plus the required brackets.

- HKS GT-SS Twin Turbos $2500

Currently on the car but im wanting a bigger setup in the car so these babies are for sale. Perfect working order and are good for 300kw. Will include manifolds and dump pipes.

- Sard 740 CC Injectors $1000

Need to go bigger so they are for sale.

- Kenwood DVD / TV Head Unit $1000

Top of the range model and still underwarranty. Touch screen, navigation, tv, dvd, mp3 and ipod connections.

- Malpassi Fuel Reg $150

Perfect working order.

- Greddy Strut Brace $150

Suit 200sx / Skyline. Used but in good condition

- S15 Floor Mats $150

Original Nissan Mats and are in good condition. Worth of $250 bran new.

- EMS Management Computer $2000

Fully programmable, does not require AFM's, will fit on any car. Similar to the Haltek computers.

- R34 GTR Engine Management Computer

Off an 99 R34 GTR Non Vspec.

- Autometer Gauge Holder

Twp c

All these parts are located in sydney and inspection is welcome. Interstate buyers are welcome but they will need to arrange transportation and cover the costs. Pictures will be up tonight.

Best way for contact is via PM or on 0449521281. Prices are firm.

Link to comment
https://www.sau.com.au/forums/topic/203923-r34-gtr-parts-and-performance-parts/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • MBS206
      Chris' Toyota Mark ii JZX110

      By MBS206 · Posted

      I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...