Jump to content
SAU Community

Recommended Posts

gees if you went too all that trouble to rebuild your motor with forged pistions why did you not just add stonger rods it would have cost the same in labour and then you could have forgot about it and it would be good for 370kw or 500hp.

I would hate to guess, so depending on variables, generally speaking it should be fine, but if its a 32gtr replacing old items with new makes sense. I take it you got upgrade turbos to handle 300kw? And seriously think of getting a N1 oil pump at this powerlevel for all day every day.

yeh they have ARP rod bolts.....I bought the car with the motor rebuilt if I did it I would have put steel rods in it, Also has an N1 oil pump and GT2860R turbos has all other components and support mods to handle 300kw just wanted to make sure the rods will be alright cause my mechanic was a bit sceptial bout it.

thanks for the info guys, also another quick question would the stock AFM's be ok for 300kw? Ive been told a cheap way around it is to you 2 rb25det ones??? Also I know this topic may have been covered aswell with a good pump and reg would the stock GTR injectors handle 300kw? I have a set of 660 nismos but im sure the $750 could be spent elsewhere if they went necassary

i wouldnt push my luck with the injectors and fuel pump when asking for 300..just generally not a smart move.

leave your AFM's as stock RB26DETT ones they will handle that fine (saving of about $600 from Z32's)

As it says guys I have had my motor rebuilt with forgies but it still has the standard rods they have just been shot peened and crack tested or something would they hand 300kw all day everyday? cheers

no problems.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...