Jump to content
SAU Community

Recommended Posts

nah u will be rite.. just pay attention next time lol..

i was part of the crue that was painting all the shit u see in there and u dont realise, but 60kms is pretty fast.

and those trucks that came thru at night with chickens on em, the smell is fu**in bad.

The Burnley tunnel is such a con! When the traffic get heavy they slow you down by 20km/hr and reduce you into 2 lanes. Sure I know 1 is fro emergency vehicle access should some nuff nuff cause another hindenberg in there. But sh!T how about some forward planing for things like that. :END RANT:

The Burnley tunnel is such a con! When the traffic get heavy they slow you down by 20km/hr and reduce you into 2 lanes. Sure I know 1 is fro emergency vehicle access should some nuff nuff cause another hindenberg in there. But sh!T how about some forward planing for things like that. :END RANT:

they also slow down the tunnels so that they can clear the fwy of accidents/roadworks furthur up with less traffic... works well, just go around the tunnels :(

Just thought Id add this useless info for the hell of it...It is possible to speed in the Tunnel and get away with it Not that I recommend it by any means. My old boss from my last company hooked up the speed cameras in the tunnel yonks ago. Their are sets of 4 faded black lines that run across the road every 300m or so i think. they are quite difficult to see in a low clearence vehicle, but at these points this is where the cameras are triggered to measure your speed. anyoo.. point of the story is u can go as fast as u want between these points aslong as your at the speed limit when you go over them.

Just thought Id add this useless info for the hell of it...It is possible to speed in the Tunnel and get away with it Not that I recommend it by any means. My old boss from my last company hooked up the speed cameras in the tunnel yonks ago. Their are sets of 4 faded black lines that run across the road every 300m or so i think. they are quite difficult to see in a low clearence vehicle, but at these points this is where the cameras are triggered to measure your speed. anyoo.. point of the story is u can go as fast as u want between these points aslong as your at the speed limit when you go over them.

the guys that did the speed cameras in the tunnels is now bankrut you do the math

the strips for the tunnel verisons re pezo strips...just slow down before you get there...make sure you know where they are, use the exit markers as a guide. If you look you can see both the cameras in the gantry and the strips on the road. its not hard.

Not withstanding they are not always on for system maintence (backend) but thats not common.

dont speed is the easy solution.

nah u will be rite.. just pay attention next time lol..

i was part of the crue that was painting all the shit u see in there and u dont realise, but 60kms is pretty fast.

and those trucks that came thru at night with chickens on em, the smell is fu**in bad.

So its you f**kers that hold me up every night when i go through there.

Piss's me off, pretty much every night (even before they started putting the wall paper up) for the last year the tunnel is reduced to 2 lanes and the speed limit reduced, it should be free when shit like that happens.

Its also a clue to how well it is built, most of the time its shut on saturday nights and there doing other work in there every other night.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...