Jump to content
SAU Community

Question About Exhausts And Joins

WYTSKY

By WYTSKY,
in Engines & Forced Induction

 Share

Recommended Posts

WYTSKY Veteran

WYTSKY

Posted
Posted

hey guys,

bought a brand new xforce highflow cat off Ryan1600 and put it on the car tonight.

With the new cat on, even with the gaskets, in the middle of the ovals on either side that join to the next part of the exhaust ( the part furthest away from the bolts) I can put my hand under there and feel some of the warm exhaust gases blowing out in the crack.

Just to make it clear... so if the top and bottem of this oval are where the bolts are, the part that I can feel gases is ... ---> () <---

Is this acceptable or does it have to be completly sealed? and if so, wot is the best way?

And I tightened the bolts up hard enough to squish the bit of the gasket around them, but not in the middle.

1 other thing, my old gaskets appeared to be larger then the ones that came with the xforce... should those maybe go back on?

appreciate the help :)

Adam

Link to comment
https://www.sau.com.au/forums/topic/205808-question-about-exhausts-and-joins/
Share on other sites
blind_elk Grand Master

blind_elk

Posted
Posted

The flange on the existing pipes has probably warped a bit. You can get special high temperature sealant (like putty) that you can coat the gasket with. That should help create a proper seal at the flange joints.

WYTSKY Veteran

WYTSKY

Posted
  • Author
Posted

Thanks guys, appreciate the help.

Can I drive the car around for the day as it is?

is it possible for me to put two gaskets on? ie, the old + new one? or is that a bad idea? because by the looks of the old 1, with that combined with the new 1 it should be a good fit.

Munkyb0y Grand Master

Munkyb0y

Posted
Posted (edited)

just use that exhaust gasket goo stuff. it's only about $10 a tube. put it on the flanges and use a gasket as you did, and hopefully it will seal. if it doesnt, you'll need to find which face is warped and get it machined flat. well not even really machined.... you could prob do it yourself with a grinder and a steady hand.

Edited by Munkyb0y
WYTSKY Veteran

WYTSKY

Posted
  • Author
Posted

I will go out and get a tube of that stuff ( sounds like it could come in handy) but I just chucked on the old and the new gaskets together and it now appears to be fine :) I may still put some stuff on it just to be safe.

Thanks for the help guys ;)

Jmaac Proficient

Jmaac

Posted
Posted

You'd be better off with two gaskets. Goo will take weeks to get it hard enough to be heat resistant. Usually melts or burns out - and its messy

If you machined it flat you shouldnt even need a gasket as the materials are the same and will be running at the same temp

If you pull it off yourself it would cost less than the goo to machine

moobaque Rising Star

moobaque

Posted
Posted

The stuff u need to buy is CRC Maniseal Exhaust Cement!

u use this stuff on both sides of exhaust gaskets and as the first time the pipes get some heat in them this stuff will set and stop all those unwanted leaks!

you can purchase it from any auto place eg. repco, bursons, supercheat, etc

WYTSKY Veteran

WYTSKY

Posted
  • Author
Posted

Appreciate the help guys.

You know, I gave the car a bit of a flog today, only for a couple of minutes, now I don't know if I have started to become used to the slight lack of power or if the power has gotten back up to what it was somehow.

you know that sensor that plugs into the cat? wot does that do? does it tell the car how much approprate flow it should have? I don't know, it just seemed to have a good strong burble session down this hill, then after that the power didn't seem to be as laggy and it feels abit more torquier from then on.

is this possible?

the other thing I am curious about. these cats flow at 570cfm or some unit of measurement. how much flow does a straight 3" pipe provide?

Adam

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • GTSBoy
      RB25 Drama's

      By GTSBoy · Posted

      Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      also possibly backed up to my filler and shat down it! 🤣
    • Julsmadrid
      RB25 Drama's

      By Julsmadrid · Posted

      Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...