Jump to content
SAU Community

Recommended Posts

Hey all,

Do anyone know the size of the standard RS4 S injectors. I am currently running approx 190rwkw with a pfc, trust front mount, full exhaust and 12.5psi

However I am getting injector duty cycles of up to 98%

I have just replaced the fuel pump however was told that the standard pump was working fine ( I replaced it really for future mods) which made no difference.

Are the stagea injectors smaller than others? I was under the impression that the stock turbo would not max out the standard injectors, and it was only until you replaced the turbo that the injectors needed upgrading.

Cheers

Dave

Link to comment
https://www.sau.com.au/forums/topic/205977-s2-rs4-s-injectors/
Share on other sites

You are getting close to max out the injectors. you could get a bit more out of them with a adjustable fuel reg.

At 98% the is no room for error. I would think with prolonged use your engine would have a short life.

The injectors in the neo are 350-370cc, cannot remember, I think they are slightly less than R33 370cc. Quick fix, turn the boost down, short term fix fit fuel reg, long term bigger injectors. I am getting at the moment 185awkw (249hp) with larger turbo, cams and blitz 525cc injectors with approx 68% duty cycle an a very safe tune.

Cheers, I think ill turn down the boost a tad. I have more mods to come soon including a larger turbo and injectors Z32 etc.

Im not going to install a FPR because of the future mods, if I was going to leave the car as it is then I would have one installed.

What sort of turbo are you running and at what boost?

What sort of turbo are you running and at what boost?

Apexi ax53b70-p25 380ps

Tomie type b 260 deg cams

Boost set at 15psi, but not holding to redline, drops back to 12.5. Need to get this sorted and run 17-18psi and a bit more timing. Runs approx 11.7:1 AFR. Tuner was worried about pushing the neo too much.

Eventually the turbo will run out of puff, so maybe upgrade to a GTRs

IF you ever do sell the Apexi turbo, let me know

:blush:

how are you going about fixing the boost drop? mine drops from 16 to 13psi, hopefully the hks actuator fixes it.

Some people on the forum, very limited amount with the apexi are getting around 250rwkw on R33 25's with full mods.

Tuner thinks it is the actuator not holding, so I have been chasing another from another member that blew his turbo running 25psi. They actually have a ceremic exhaust wheel supposedly, but are way stronger than the factory nissan wheels.

It does pull well from 3500rpm. The apexi's are reportedly to have good midrange and the cams help out well

I was hoping to get to the track to see what it would do, but it keeps raining. That is is where the true performance is shown, not by a dyno result.

I saw your dyno sheet, and it looks like you have a lot of boost drop off up top which if correct will see a large power gain.

The tuner spent over an hour playing around and adjusting the boost controller and the actuator, but could not get it right. So hopefully when sorted there will be an extra 20-40kw.

DEATSCHWERKS injectors look the shitz

the ones I got delivered this week are high-flowed 480 to 550cc items

Im sure they would be able to do top feed.

they are in the States, email and ask for david or mike and say Brendan from South Australia referred you.

DEATSCHWERKS injectors look the shitz

the ones I got delivered this week are high-flowed 480 to 550cc items

Im sure they would be able to do top feed.

they are in the States, email and ask for david or mike and say Brendan from South Australia referred you.

I would suggest the Blitz 525cc over the Deatschwerks, as the blitz are new and the same price delievered from greenline and are not reco highflow's. Just my opion.

for sure

I went based on price - and factored in the fact that Im only after 20 more a/rwkw anyway.

they charged me bugger all, around $400 all up (they stuffed up, I wanted custom 450cc items they said have 550cc no extra)

I think ill leave t up to my tuner, I have previously used ~560cc denso injectors in an R33 which were fine for my application. Im building the car for the GTRS at approx 18psi however want a little room to move if I decide to go a bigger turbo again later on down the track.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • And if you want more power, more reliably, and cheaper, go get the Aussie RB... The 4L Barra and put that in instead.
    • No cats will keep discolouring the rear bar. Sends white paint a weird yellow stain. Cut and polish normally gets it out, but you'll be doing that every fortnight I found.
    • Both heads will be equally reliable or unreliable depending on what you do to them.  Stock the RB26 head will flow more. You have access to the stock intake ITB manifold on the RB26 cheaply which flows really well(1000hp+).   Arguably more aftermarket support for RB26, though in Aus we love our RB30 SOHC heads too.    The only downsides to the RB26 head is if you have a VL commodore and want to keep the SOHC look.  Where you may have an issue is drilling out the rb30 block for the bigger head studs but if you are building a big power motor you'd probably put bigger studs on the SOHC head too.  This is just about finding a good machine shop, sometimes easier said than done.  RB30 head worked can make big power just like a Rb26 head, so really it actually more comes down to what your preference is for your car.  People now even making billet versions of both.
    • 2630s work perfectly well. There is something to be said for just using the 30 head, as it saves all the pain of the conversion, still makes tons of power, still sounds cool, etc etc. 2630 will obviously make more power again, but the differences are not stupidly big. It really depends on whether you're racing for sheep stations or not. If it's dead serious, then it's a 26 head. If it's just for fun, it could go either way. But the 26 head and the effort to get it set up, etc etc, is part of the fun.
    • I've been building a 26/30 for a few years now. I've had the head built with all the good stuff. I had a 32 gtr but blew it up and yes its all going into a vl but im looking for some advice from some RB nuts on pros and cons on putting a 26 head on a 30 bottom end is it worth it Works are as follows Head -Extensive porting 1mm oversized supertech valves Supertech double springs Supertech valve guides Supertech titanium retainers Tomei solid lifters Tomei 270 x 10.25 cams Head drain Bottom end series 2 rb30 block Cp ceramic coated pistons Eagle rods Romac balancer Oil restrictions  O ringed blah blah spent a fortune And will get a girdle because the 30s arent used to handling that much rpm Nitto billet oil pump Hypertune plenum 6boost mani Refurbed astra pump thats the cover for it in the boot I did have a precision 6262 but sold it because drag car life. Currently building the ass end full 4 link floater rear end with a 2 speed  But the dilemma i have is my mate rekens I should just stick with the 30 head for reliability. Has any one had any issues with mounting the 26 head ie compression blowing gaskets etc. Just looking for some advice from people who have gone down this route. Here's some photos. Blew the oil pump in the gtr and decided to rip the motor out at the time and do a full build only to find it had been a repairable write off so went down this path.     
×
×
  • Create New...