Jump to content
SAU Community

Recommended Posts

  • Replies 58
  • Created
  • Last Reply

Top Posters In This Topic

Had an auto line once.zdenko if you put a stally and decent tyres you easily get a 13sec.i put 3500rpm stally in mine and was mad takin off with full boost.your 60fts would be mad low(with traction).let me know if you wanna buy one as i know the bloke who owns dominator.and can get you a good deal

Hey danny,

you were running 14PSI you lying ****! =P

And 34-GTR i saw your first run. =(

15.00..... and then your second 13.?? then your last 12.??

was it your first time down the quater?

you ran pretty well dude, noticed your changes were a little late through your changes. and on your first run i heard the revlimiter on every gear! =)

Never the less you made it into the low -12s witch you should be more than happy with.

Originally posted by JNR24

Hey danny,

you were running 14PSI you lying ****!  =P

And 34-GTR i saw your first run.    =(

15.00..... and then your second 13.?? then your last 12.??

was it your first time down the quater?

you ran pretty well dude, noticed your changes were a little late through your changes. and on your first run i heard the revlimiter on every gear!  =)

Never the less you made it into the low -12s witch you should be more than happy with.

tell me about it man...my first run i got 13.2s or something was pretty shit and then my 2nd i did 15sec ohh f**k it was embarassing man... ididnt konw what the hell was going on, i was in third gear and it was still spinning the tires until it stopped spinning and the revs dropped and then i went properly..I was used to the car before with high revs and shit, didnt even know about the rev limiter until at the end of the day my dad was going it was limited at 8,000revs..On the last run he upped the limit to 9,000 and did the 12.3 sec pass...It was my 2nd time dragging and this was the worst of all didnt know why.:(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...