Jump to content
SAU Community

Recommended Posts

On closer inspection Craig has a valid point. Looking at your pic the flap is off centre to the machined hole.

i second that, i would get him to increase the machined lip around the gate hole just to be sure, i reckon the left hand side is sitting up on the rough casting... not in the machined ring.

what waste gate actuator are you running?

is it the stock 8 psi one?

maybe try a heavier one say 18psi.

also with the flapper would it be possibe to do a 3 angle valve grind on it to increase the seating area?

here are some pics

**EDIT** sorry should've added i know it is leaking as i can hear it on the screamer pipe, and when i put my hand over the screamer pipe (can feel gasses) to create a seal the exhaust note changes slightly...

are you using a dump gasket? ie a ford xr6 gasket?

that seperates the wheel from the gate?

the turbo housing is divided into two section completely sep from each other

on the turbo side of the dump it has a smaller pipe weld into it so when fitted upto the turbo it pushes inside and seals even more

his using a copper crush gasket

the actuator seems to be wrong for the application seeing as you cant preload the crap out of it

at full tight it is maybe half a cm away from the arm at the arms full closed postion

this would also mean you'd have to bleed off a yeap of air via the boost controler to get the correct boost

(assuming its not running close the boost level you want just using the arm as it is)

I say buggar it and run it up again

The std screw on bit for the actuator that came with my gt3076 was too short; I had a longer one made up.

I have around 2mm preload which grabs 15psi and with the actuator at full reach allows the flap to open almost 90degree's.

2mm is approximately what the std turbo and std actuator has factory.

If you place too much preload you will experience boost creep as the for every extra mm preload you place on the gate you loose with the max opening angle.

Starting to go a little OT but what the hell. :D

The only downside with very little preload is especially with the garrett 1bar actuators with the kink in the rod is they are lazy. With just the actuator I was seeing 8psi at 2500rpm, 11psi at 3000rpm and then 15psi at 4500rpm.

With a cheap ball/spring bleeder on it it was making 19psi at 3100rpm. Thats a huge improvement in peak boost. ~1400rpm.

For myself I was told the GT30's will boost creep if you don't run with a Bell mouth or at least put some effort in to the dump pipe and design it as HKS do.

HKS have created the opening of the wastegate pipe as large as possible; this allows maximum gas flow with no hard edges for the gas to hit.

The problem with the usual 3" and 2" wastegate style dump with the GT30's is when the flap opens it is unable to open a full 90degree's which would allow the full 2" opening of the wastegate pipe to be utilized; when its open say 45degree's with reasonable preload it partially blocks that 2" opening which is why these style dumps almost always boost creep with the GT30's.

I followed the advice of who does the tuning on my car and with the std sized flapper but with a .8 rear I experience zero boost creep on the 3ltr by running minimal preload and a nice open bell mouth. Yes with out a boost controller boost is lazy but who cares thats what an ebc is for.

HKS dump opening attached.

All IMO. :)

post-382-1203905728_thumb.jpg

i ordered a 14psi actuator - so i assume that is what it is.

i'm not trying to solve the response issue etc at the moment. just eliminate the leaking - i'm coming to the belief that it possibly doesnt seal when the flap sometimes seals in a different position. (flap not fixed position)

i'm under the impression that 'if' i didn't go for the screamer setup then i wouldn't even be aware of the leaking issue...

*sighs...

Edited by huddy

plan G

grab a g clamp or similar contraption and clamp the sucker shut.

if you remove the actuator arm at the pivot point and then wiggle the flapper to see if you can feel a happy spot where it wants to shut, then clamp it shut.

this then will prove if its the gate the actuator or the dump design.

i have a sneeking suspicion that is not the wastegate but the main outlet not sealing properly.

due to not using a ford gasket.

this copper gasket you mention is something you made or the cheap crap you get from an exhaust shop.

also have you had the dump flange milled flat?

come to think about it im not sure why the dump needs the peice of pipe welded on the flange as its a different hole to the wastegate you just need a propper gasket.

thanks for all the brainstorming guys :)

on that last sentence - i agree and originally it did not have the pipe welded onto the flange... but it was leaking so first thoughts was 'must be the dump design..'

the gasket was provided by and has been used by the exhaust maker (Andrew) many times previously and had no problems whatsoever on many other setups (including screamers)

i will try the G Clamp idea to suss out if it is the actuator (i doubt it though as it's brand new, and has a LOT of tension on it already)

any more ideas for me to try??? :/

Just a quick question

How much should a wastegate flap actually open, i am using a hks 3037 pro s turbo kit which comes with the hks dump that Cubes posted a pic of, but i have noticed if i desconnect the actuator arm and try to open the wastegate flap using the part that the actuator rod clips onto i can only move it about 1cm untill it hits the dump pipe.

Does this sound normall?

Im sure it would be fine as HKS surely wouldnt have overlooked this and would have desinged the kit to work perfect.

thanks for all the brainstorming guys :D

on that last sentence - i agree and originally it did not have the pipe welded onto the flange... but it was leaking so first thoughts was 'must be the dump design..'

the gasket was provided by and has been used by the exhaust maker (Andrew) many times previously and had no problems whatsoever on many other setups (including screamers)

i will try the G Clamp idea to suss out if it is the actuator (i doubt it though as it's brand new, and has a LOT of tension on it already)

any more ideas for me to try??? :D

when the extra peice of tube was welded onto the dump flange was the flange milled flat?

the heat from welding it would have worped it to some degree.

and just so you know the ford xr6 gasket is stainless steel multi layer jobby that cost around $16

if your flange is flat and you run one of these you can completely remove it from the problem list.

Hi Dangerman

well once again i 'assumed' it was flat when the work was done...

...saying that though I JUST REFITTED IT ALL UP AGAIN...

and it is NOT leaking!

so i am completely clueless... as it seems to be inconsistent... i will keep an eye (or ear) on it to hear if it leaks again - if it does, then i'm thinking wastegate flap (when it rotates).

thanks, i will keep this thread updated.

being the waste gate is metal on metal it would either seal or not seal.

so im sticking with the dump not being 100% flat and this time you have stuck just the right amount of goop in the right spot to seal the turbine from the screamer.

glad its fixed either way.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...