Jump to content
SAU Community

Recommended Posts

Item: GT3040 0.63 rear 0.7 front, turbo kit, stainless manifold, Tial 38mm wastegate, braided oil + water lines

Age: prob only 5000km

Condition: like new

Price: $2500 ono

To Fit: (What car) RB20. RB25

Location: Adelaide SA

Contact: 0431257754

Comments: only ever run 13psi with few short spurts at 17psi. includes polished intake pipe and K&N filter

Item: Microtech LT12s plug n play computer with hand controller

Age: 5000km

Condition: like new

Price: $1000ono

To Fit:RB20DET

Item: EBoost 2

Age: 5000km (if that)

Condition: like new

Price: $500

To Fit: anything

Item: RB25DET built motor by RACEPACE

Age: 10000km

Condition: excellent

Price: $3500

To Fit: anything

Comments: aries pistons, RB26 rods, N1 oil pump, tomei cams + gears, metal head gasket. everything done. have dyno sheet for only 285rwkw. could handle lot more

Item: 19 row oil cooler and filter relocator

Age: 5000km

Condition: excellent

Price: $250ono

To Fit: RB20

Comments: all braided lines, anodised

also large front mount, full set of autometer sport comp silver mechanical guages, oil pres, water temp, boost and monster tacho,

720cc siemens top feed injectors with big rail to suit rb20det with speedflow fittings $650ono

bosch 044 fuel pump, 1.5L surge tank

throttle body, coilpacks, heaps of other little things

selling everything... make an offer. will post at your expense. im in adelaide

no time wasters. all must go. need the room

leave your email if you want pics

adrian 0431257754

i not on here often so call or message

Edited by VLT020
  • 2 weeks later...
  • 2 weeks later...

ok. everything was sold but has fallen through so its all up for grabs again. selling whole car so make an offer on anything. best i dont check this often so call or message on 0431257754 or [email protected]

720cc siemens top feed injectors with big rail to suit rb20det with speedflow fittings $650ono

bosch 044 fuel pump, 1.5L surge tank

hey man is this all for this price

pics would be nice

and have the injectors been flow tested and cleaned or are they brand new

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...