Jump to content
SAU Community

Recommended Posts

If you are doing a stay-at-home type bbq and beer, with b00bies etc, then I can thoroughly recommend brewing the beer yourself at one of these brew on premises places. I used one last year for a bucks party and it went down a treat! Most places will hire you keg setups, and you just tell every one to bring their own mug - less clean up and you save on glass hire :D

Link to comment
https://www.sau.com.au/forums/topic/209540-bucks-night/#findComment-3706236
Share on other sites

Wheelie Bin,

Cut hole for his head on the front of it, holes for his arms on the sides, lock him in it and take him to the strippers and to pub and clubs....... Happened to me and I loved it (Was In Sydney at the time)

Link to comment
https://www.sau.com.au/forums/topic/209540-bucks-night/#findComment-3707125
Share on other sites

Wheelie Bin,

Cut hole for his head on the front of it, holes for his arms on the sides, lock him in it and take him to the strippers and to pub and clubs....... Happened to me and I loved it (Was In Sydney at the time)

Pictures? Where did you piss? lol!

Link to comment
https://www.sau.com.au/forums/topic/209540-bucks-night/#findComment-3707185
Share on other sites

Book a table at a nice restaraunt, everyone wears a tuxedo, order great food and wine and ....stuff it, BBQ, eski full of coldies, skimpies to serve and strippers OR you could hire a boat and take the party to the water, that way the party finishes when its time and no noise problems...book a bus to get everyone home in one piece

Link to comment
https://www.sau.com.au/forums/topic/209540-bucks-night/#findComment-3709831
Share on other sites

have been to afew bbq boobs and beer and its always a good night

for my brothers we were a little more refined we hired a boat and cruised the river enjoying bbq several kegs from little creatures and poker

boobs would have made it better but was still good fun

if your going with the barbie at home idea i sugest 1/2 skimpies to serve drinks with a striper later in the night

nothing better than a cold one served by a nice set followed by a show lol

Edited by GWP021
Link to comment
https://www.sau.com.au/forums/topic/209540-bucks-night/#findComment-3714396
Share on other sites



  • Similar Content

  • Latest Posts

    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
×
×
  • Create New...