Jump to content
SAU Community

Recommended Posts

Sorry, wasn't able to answer this question, but did they fit?

I have just found some info' on globes for the (standard) climate control:

This was from this thread under the DIY sticky:

http://www.skylinesaustralia.com/forums/in...t&p=3333939

Nah they don't fit, the LED's don't fit through the hole - Oh well at least I can change my dash lights down the road.

Well I was looking at Jaycar and saw those grain of wheat lights and saw two different ones

post-34764-1207576165_thumb.jpg

This one the dimensions - Globe size - 4mm dia x 10mm PVC lead length - 150mm Current - 0.1A 12V (Yellow light)

the other is this one

post-34764-1207576178_thumb.jpg

This one the dimensions - Globe size - 3mm dia x 7mm PVC lead length - 100mm Current - 0.1A 12V (Yellow light)

Now I don't know which one to get? what do you guys think??

From memory new ones from Nissan are about $3 each.

I recommend changing all of them at the same time - else you'll have slightly dull areas where the old blue covers have faded.

Edited by BensDR30
can you remember the part number for it Ben (if there is one)

Ok, so my prices were a bit off...

(Note that theses prices might be trade, and were from Nov. 2004)

27545-8E500 $11.00 ea

27545-0N002 $11.50 ea

I bought 2 of the 1st & 4 of the second. That should be enough info to work out which size is which.

Edited by BensDR30

Cool thanks...I'll keep that those part numbers in mind

I got the globes from jaycar - thought they were just a solid wire when you strip the insulation off but its those thin multi wires (don't know the proper name). trimed them and put then in the holder (after cutting and fitting the plastic bit where the bottom of the globe/wires are) put the blue covers on and now i can't finally see my climate control at night

Cool thanks...I'll keep that those part numbers in mind

I got the globes from jaycar - thought they were just a solid wire when you strip the insulation off but its those thin multi wires (don't know the proper name). trimed them and put then in the holder (after cutting and fitting the plastic bit where the bottom of the globe/wires are) put the blue covers on and now i can't finally see my climate control at night

Good news! well done

  • 2 months later...

i went to autobarn and picked myself up some of there small wedge type LED's bent the wires out of the blue plastic "wedges" and pulled them out, put them back into the climate control globe holders and done,,, blue backlight for the LCD and also for the buttons. all up cost me 10 bux :D

post-36893-1215782995_thumb.jpg

post-36893-1215783039_thumb.jpg

i went to autobarn and picked myself up some of there small wedge type LED's bent the wires out of the blue plastic "wedges" and pulled them out, put them back into the climate control globe holders and done,,, blue backlight for the LCD and also for the buttons. all up cost me 10 bux :)

awesome stuff, thanks for the info!

i went to autobarn and picked myself up some of there small wedge type LED's bent the wires out of the blue plastic "wedges" and pulled them out, put them back into the climate control globe holders and done,,, blue backlight for the LCD and also for the buttons. all up cost me 10 bux :D

I bought the same type of led's from Autobarn, I'll give it a go after work tomorrow with my A/C. Cheers for the tip!!

  • 7 months later...
i went to autobarn and picked myself up some of there small wedge type LED's bent the wires out of the blue plastic "wedges" and pulled them out, put them back into the climate control globe holders and done,,, blue backlight for the LCD and also for the buttons. all up cost me 10 bux :D

i went into autobarn, supercheap, repco, jaycar and dicksmith today and none had anything like you were talking about... they had the t5 lights in a holder but they had like built in resisters which made it much larger and unable to mount in the original holder.. can you post some pics of the ones you got or can anyone tell me where to get the "wheat" style globes??

Thanks

curt

ok after that i think i have find what we are looking for its as posted in post #14, here is the website - http://www.dse.com.au/cgi-bin/dse.storefro...n/product/P8140

they are 12v, 5mm wide and with pigtails to wrap around the original holders.. i'm going to the shop tomorrow and i'll let you know how i go and post some pics..

and the best thing, there only $1.28 ea

Thanks

curt

are you replacing the globes in the middle section of your climate control or the lights that light up the controls. because the control lights are very small and I don't know if the lights you are getting from DSE will fit in there. They will fit in the centre light holders (the climate control display). just get some coloured condoms to go over them if you want to keep that silvery type colour...or else they go orange

I'm just pissed off now that 3 out of the 4 control lights are blown...and now i've got to replace them...and i've lost the blue covers from them aswell

well... the lights fit but.. with the 4 back ones i had to take apart the unit and there are 3 screws inside on the front board, undo them slighty and install those and do it up until its tight but not too tight. reassemble and should be all ok.. just make sure the wires make contact with the board.. also with these bulbs they are only orange in colour unless you kept the coloured condom things.

  • 3 weeks later...
Hi Guys,

I need to know where I can get replacement globes for my climate control...it still works but the backlight has gone. Also how do i go about changing the lights in the climate control

Same problem here mate, my system works but the display has shit itself, im currently checking out scrap yards and people that are wrecking skylines. r32 + r33 ACU's are pretty generic.

Good luck

  • 7 months later...

All the bulbs for my Climate Control are burned out.

I was going to put blue LED's in my Climate Control and Dash today (nothing wrong with dash) but ran into a few issues.

First the LED's I bought for the Climate Control were supposed to come with resistors, I was going to find the power wire for the bulbs and hardwire resistors before the plug, but when the LED's arrived there were no resistors dodgy EBAY was an Aussie company as-well =(.

Tried wiring one up without a resistor but it burned out instantly.

The LED's I got for the Dash cluster have the resistors built in - sweet, but my dash apparently has that filter stuff that blocks out blue =( so I had to put the standard bulbs back in as almost no light penetrated the filter.

I gently removed the LED's for the Dash from their holders and fed the legs through the holders for the Climate Control bulbs, I had to squish them a bit to get everything in and then squish the led's closer together (they are the multi direction type with 3LED's) to fit them through the mount holes. Works great I was really surprised.

I noticed some people were missing the blue condoms from the standard bulbs that make the light white, I have a full set of these left over now so if anyone wants them just let me know ill bang em in the mail. It'd be a shame to throw em out if someone could use em.

I noticed some people were missing the blue condoms from the standard bulbs that make the light white, I have a full set of these left over now so if anyone wants them just let me know ill bang em in the mail. It'd be a shame to throw em out if someone could use em.

i messed up a couple of mine yesterday

i'll take them if they're on offer :D

PM me details please

:down:

  • 2 weeks later...

PM sent Oppression :)

all the DSE's around me don't have the wheat globes in stock

Repco reckons they can't get the globes

Supercheap were no help

i bought some of these ( http://www.jaycar.com.au/productView.asp?I...mp;form=KEYWORD ) from Jaycar and am going to try and make them fit

anyone found a reliable source for these globes yet?

Edited by Stooge007
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...